ADLINK Technology CoreModule 740 Скачать руководство пользователя страница 26

Страница: 26 / 46

Chapter 3

Hardware

Reference Manual

CoreModule 740

Note:

The shaded areas denote power or ground. The signals marked with * indicate active low.

USBN1-

USB Port 1 Negative Polarity

PP_PE

Parallel Paper End – This is a status output signal from the printer. A high state
indicates it is out of paper.

USBP1+

USB Port 1 Positive Polarity

GND10

Ground 10 (USB)

GND11

Ground 11 (USB)

PP_SLCT

Parallel Select – This is a status output signal from the printer. A high state
indicates it is selected and powered on.

USB_OC2* USB 2 Power Protection – Port is disabled if this input is low. Direct inputs are

provided for over current protection.

FIRMode

IR Function Mode Select – Tied to ground through 10k ohm resistor.

USBPwr2

+5 volts +/-5% (USB2 Power)

Not Connected

USBN2-

USB Port 2 Negative Polarity

GND12

Ground 12 (USB)

USBP2+

USB Port 2 Positive Polarity

IRTX

Not Connected

GND 13

Ground 13 (USB)

IRRX

Not Connected

MDATA

Mouse Data

SPKR

Speaker – Signal for external PC “Beep” speaker.

MSCK

Mouse Clock

GND14

Ground 14 (Mouse)

GND15

Ground 15 (Mouse)

ResetSW

Reset Switch – Accepts external reset signal (momentarily grounding this pin.)

MSPwr

+5 volts +/-5% (Mouse Power)

KBSW

Not Connected

HDACT

IDE Hard Drive Active – Signal for external HDD activity LED.

KBDT

Keyboard Data

ExtSMI

Not Connected

KBCK

Keyboard Clock

Not Connected

GND16

Ground 16 (Keyboard)

Not Connected

KBPwr

Keyboard Power

-12V

Not Connected

BATV+

External Backup Battery Positive – External positive battery terminal.

-5V

Not Connected

BATV-

External Backup Battery Negative – External battery ground.

Table 3-4. Utility 1 Interface Pin Signals (J5) (Continued)

Содержание CoreModule 740















































Результаты поиска

Содержание CoreModule 740

Отзывы:

Похожие инструкции для CoreModule 740

Бренды по названию

Популярные бренды

ADLINK Technology CoreModule 740, Справочное руководство

Результаты поиска

Содержание CoreModule 740

Отзывы:

Похожие инструкции для CoreModule 740

Бренды по названию

Популярные бренды