P
ower Supply:
Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your ADJ Pixel
Kling 10C. Because line voltage may vary from venue to venue, you
should be sure your unit voltage matches the wall outlet voltage before
attempting to operate you fixture.
DMX-512:
DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav-
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-
minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking:
DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Pixel Kling 10C can be controlled via DMX-512 protocol. The Pixel
Kling 10C has 4 DMX channel modes, please see page 7 for the different
DMX modes. The DMX address is set on the back
panel of the Pixel Kling 10C. Your unit and your
DMX controller require a standard 3-pin XLR con-
nector for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all pro lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
Pixel Kling 10C Set Up
ADJ Products, LLC - www.adj.com - Pixel Kling 10C User Manual Page 5
Figure 1
ADJ Products, LLC - www.adj.com - Pixel Kling 10C User Manual Page 22
Channel Value
Function
1 RED (TUBE 1 PIXEL 1)
0 - 255 0% - 100%
2 GREEN (TUBE 1 PIXEL 1)
0 - 255 0% - 100%
3 BLUE (TUBE 1 PIXEL 1)
0 - 255 0% - 100%
4 RED (TUBE 1 PIXEL 2)
0 - 255 0% - 100%
5 GREEN (TUBE 1 PIXEL 2)
0 - 255 0% - 100%
6 BLUE (TUBE 1 PIXEL 2)
0 - 255 0% - 100%
7 RED (TUBE 1 PIXEL 3)
0 - 255 0% - 100%
8 GREEN (TUBE 1 PIXEL 3)
0 - 255 0% - 100%
*Channels 9-472 Continues the same RGB Tube Pixel pattern*
473 GREEN (TUBE 10 PIXEL 14)
0 - 255 0% - 100%
474 BLUE (TUBE 10 PIXEL 14)
0 - 255 0% - 100%
475 RED (TUBE 10 PIXEL 15)
0 - 255 0% - 100%
476 GREEN (TUBE 10 PIXEL 15)
0 - 255 0% - 100%
477 BLUE (TUBE 10 PIXEL 15)
0 - 255 0% - 100%
478 RED (TUBE 10 PIXEL 16)
0 - 255 0% - 100%
479 GREEN (TUBE 10 PIXEL 16)
0 - 255 0% - 100%
480 BLUE (TUBE 10 PIXEL 16)
0 - 255 0% - 100%
Pixel Kling 10C 480 Channel - DMX Values & Functions