A.D.J. Supply Europe B.V.
– www.americandj.eu – Mega QPlus Go Instruction Manual Page 11
This mode can be used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen
in the setup is the running mode the fixture will go into when the DMX signal is lost. You can also set this as the
operating mode you would like the unit to return to when power is applied.
1. Plug the fixture in and press the MODE button until “d.XXX” is displayed
.
“XXX” represents the current
displayed DMX address.
2. Press the SET UP button so that “nodn” is displayed. Use the UP and DOWN buttons to scroll through the
DMX states.
• “bLAC” (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.
• “LASt” (Last State) - If the DMX signal is lost or interrupted, the fixture will stay in the last DMX set up. If power
is applied and this mode is set, the unit will automatically go into the last DMX set up.
• “ProG” (Auto Run) - If the DMX signal is lost or interrupted, the unit will automatically go into Auto Run mode.
3. After you have found your desired setting, press SET UP to exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See page 16 for the dimming curves chart.
1. Plug the fixture in and press the MODE button until “d.XXX” is displayed
.
“XXX” represents the current
displayed DMX address.
2. Press the SET U
P button until “dr-X” is displayed. “X” represents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your desired dimming curve.
Activate IR Sensor:
This function is used to activate and deactivate the IR sensor. When this function is activated you can control
the fixture using the UC IR, or Airstream IR App. Please see page 11 for controls and functions.
1. Plug the fixture in and press the MO
DE button until “dXX” is displayed
.
“XX” represents either “on” or “oFF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote function (On) or deactivate it (Off).
Default Running Mode:
This is a default running mode. When this mode is activated all modes will return to their default settings.
1. Plug the fixture in and press the MODE button until “dXX” is displayed
.
“XX” represents either “on” or “oFF”.
2.
Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE button to exit.
MASTER-SLAVE CONFIGURATION
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave set-up. In a Master-Slave set-up one
unit will act as the controlling unit and the others will react to the controlling units built-in programs. Any unit can
act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link
your units together. Remember that the Male XLR connector is the input and the Female XLR connector is the
output. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will
use the male XLR connector only.
2. Connect the first “Slave” unit to the “Master.”
3. Set the “Master” unit to your desired mode of operation. Set the “Slave” unit(s) to the DMX address setting of
001.The “Slave” unit(s) will now follow the “Master”.