manualshive.com logo in svg

ADJ GALAXIAN 3D MKII, Инструкция пользователя

Поделиться
Скачать
ADJ GALAXIAN 3D MKII Скачать руководство пользователя страница 6

ADJ Products, LLC  -  www.adj.com - Galaxian 3D MKII Instruction Manual Page 12

ADJ Products, LLC  -  www.adj.com - Galaxian 3D MKII Instruction Manual Page 11

System Menu: When confirming your setting press ENTER 

and then hold MENU for at least 2-3 seconds, or you can 

wait 1 minute for automatic setup. To exit without making 

any adjustments press the MENU button. 

ADDR -

 

DMX Address Setting

.

1. Tap the either the MENU, UP, or DOWN buttons until “ADDR” 

is displayed, press ENTER.
2. The current address will now be displayed and flashing. 

Press the UP or DOWN buttons to find your desired address. 

Press ENTER to set your desired DMX address. 

SLND -

 This will let you set unit as a master or slave in 

a master/slave configuration.

1. Tap the MENU button until “SLND” is displayed, press 

ENTER. Either “SL 1” or “SL 2” will be displayed.
2. Tap the UP or DOWN buttons until your desired setting is 

displayed, press ENTER and then hold MENU for at least 2-3 

seconds to confim.
NOTE: In a Master/Slave configuration you can make one 

fixture the Master and then set the next fixture to “SL 2”, the 

fixtures will now have contrast movement to each other. 

SOUN -

 Sound Active mode.

1. Tap the MENU button until “SOUN” is displayed, press 

ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or 

DOWN buttons to select “ON” to activate sound active mode, 

or “OFF” to deactivate sound active mode.
3. Press ENTER and then hold MENU for at least 2-3 seconds 

to confim.

 Galaxian 3D MKII   

 

 

            System Menu

 Galaxian 3D MKII   

                      System Menu Chart

Содержание GALAXIAN 3D MKII











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды