ADF LINEA NMV Скачать руководство пользователя страница 4

20°C change in temperature. 

Once chose

n

, to save the Preferred Selected speed, press the ON button, or wait 5 

seconds. 

2.

To go into the Main Menu, hold the Menu button for 3 seconds.  Press the Menu

button to scroll through setting options.  Press the UP and DOWN 

button 

to change

the

 

value.  Press the MENU button to save the new setting.  Wait 10 seconds or

Press

 

the ON button to exit.

3.

Safety Function:  In Manual mode, if the Thermostat reaches 100°C, the Fan will

switch to the Proportional mode to prevent electricals from overheating.

If the fan is OFF, and the Thermostat reaches 100 to 120°C (E02 to E03), the Fan will

switch ON to prevent electricals from overheating

4.

Alarm Function:  If the Thermostat reaches 120°C (E03), an audible and visual

alarm

 

will sound/flash.  Press any key to turn alarm off for every 5mins until temp

drops

 

below 120°C.  To turn off Alarm function change P05 setting (see page 16 ).

5.

Fan Safety cut off:  If the thermostat reaches 135°C (E04), the Fan will cut off to

avoid Damage to itself.

6.

Thermostat Temperature Display: By pressing the MENU button once, the 2

nd

Thermostat Temp will display (If fitted).  To exit press the ON button.

Note: If Thermostat temp is below Minimum, it will display Lo.

If Thermostat temp is above Maximum, it will display Hi. 

Содержание LINEA NMV



















Отзывы: