6
Step Action
Display
Enter [4] (Loop Functions). Enter the loop number (1-4).
Note:
The 6128RF is shipped with the loop functions preprogrammed.
Perform steps 6 through 10 only if it is necessary to change any
of the loop functions.
Loop 1
Close the 6128RF On-Board Relay for 2 sec.
Loop 2
1 (Disarm)
Loop 3
2 (Arm Away)
Loop 4
3 (Arm Stay)
See the Wireless Key Function Chart below for the choices:
Wireless Key Function Chart
Function Entry
Disarming 1
Arming Away
2
Arming Stay
3
Arming Maximum (Away Instant)
4
Arming Instant
7
Panic Alarm
Produces type of alarm [* & #]
programmed in control panel.
# + 99
Manually Start a Relay Action
# + 7
(VISTA-10SE, VIA-30PSE)
# + 7 + n
(VISTA-10P, VISTA-15P,
VISTA-20P, VISTA-20PS,
VISTA-20SE, VISTA-20HWSE)
Manually Stop a Relay Action
# + 8
(VISTA-10SE, VIA-30PSE)
# + 8 + n
(VISTA-10P, VISTA-15P,
VISTA-20P, VISTA-20PS,
VISTA-20SE, VISTA-20HWSE)
Activate Relay as Programmed in
Control
# + 71
(VISTA-40, VISTA-50P)
Activate Relay as Programmed in
Control
# + 72
(VISTA-40, VISTA-50P)
Activate Access Control Relay for
Partition
0
(VISTA-40, VISTA-50P)
n = Device Number programmed into these panels to be controlled
6
Press the [
✳
] key.
Flashing "Ln."
Once the loop number is
entered, alternately flashes
"L" with the loop number
and the present function.
Default Loop Functions
LOOP 4
Arm STAY
LOOP 3
Arm AWAY
LOOP 1
Close on-board relay
for 2 seconds
LOOP 2
Disarm
ON
OFF
5 8 0 4 - 0 0 2 - V 0
5804
•
•
••
•
•
•
•
•
•
•
•
•
• •
•
•••
LOOP 3
Arm AWAY
LOOP 4
Arm STAY
LOOP 1
Close on-board relay
for 2 seconds
LOOP 2
Disarm
5 8 0 4 B D - 0 0 2 - V 0
5804BD
SET
HOUSE
CODE
7
Repeat step 6 for the rest of the loops of the wireless key.
8
To program a button on the wireless key to control the on-board
relay, enter [5] (On -Board Relay Assignment).
Flashing "o-."
9
Enter the loop number of the wireless key (1-4). Enter the relay
action (0 = no action; 1 = relay off; 2 = relay on; 3 = relay toggles on &
off; 4 = relay closes for 2 seconds).
Note:
The relay action must be "0" for UL installations.
Press the [
✳
] key.
Flashing “o” and the loop
number.
Once the action is entered,
the display will show “o”
and alternately flash the
loop number and the relay
action.
10
Repeat step 9 for the rest of the loops.
11
When all loops have been programmed for the wireless key, press the
[
✳
] key.
Flashing “d” followed by the
device number.
12
The 6128RF will automatically display the next available device
number (one that does not have a serial number).
If you desire to program additional wireless keys, repeat steps 3
through 10. Otherwise, press the [
#
] key. This will take you back to
the main display, that will alternately flash “oo” and “- -.”
Press the [
✳
] to exit the 6128RF Program Mode.
Note:
Upon exiting of the Program Mode, the 6128RF will alternately flash "Ad," the 2-digit keypad address,
and the 2-digit receiver address. If either of these is incorrect, repeat steps 1 through 3 under
Programming for
an Installation Without Local Wireless Keys
.
