background image

www.addonics.com

Technical Support (M-F 8:30am - 6:00pm PST)   

Phone: 408-453-6212 

Email: www.addonics.com/support/query/

6.8. Calc. Checksum

Calculates a checksum value for the  Copy Area function defined in the 

Setup Menu.

NOTE: This function is not to be used to validate copies. Media that have 

identical content and structure may still have different checksums. Testing 

media devices for accurate duplication should only be done using the 

Compare function.

Setup Menu
7.1. Startup Menu

Defines the function that will appear by default after power-on testing is 

completed. Any of the Main Menu functions may be selected.

Default is 1. Copy.

7.2. Copy Area

Determines the method for copying from the source device to the target 

devices: “Whole Media” copies the entire device, sector-by-sector – without 

any regard to the contents. “System and Files” copies only the contents of 

file systems understood by the firmware: FAT16, FAT32, NTFS, ext2 or ext3. 

File systems not recognized by the firmware will be copied using the “Whole 

Media” method.

Default is “System and Files.”

7.3. Button Beep

Enables or disables the unit sounding a “beep” noise when buttons are 

pressed.

7.4. Asyn Hold Time

During operations that use Asynchronous Mode, this setting determines the 

delay after all media have been removed before confirming that an operation 

is complete. Once that delay has been expired, the operation will halt and 

the display will request confirmation to exit the function. Press OK to confirm 

the exit, ESC to resume the function.

Settings are “Turn OFF” to disable this feature, meaning Asynchronous 

functions will continue indefinitely until ESC is pressed, or a selection of 

delay in seconds or minutes.

Default is “Turn OFF.”

7.5. Target Tolerance

Used to define the acceptable difference in capacity during the copy func-

tion, using one of three settings:

No Limit: Target capacity will not be considered before proceeding.

100% Same: Target capacity will be considered suitable only if the capacity 

is identical to the source.

Allow tolerance: Selecting this option offers two additional choices: Set UP 

Limit allows either “No Limit” or a percentage greater than the source 

capacity. Set LOW Limit allows either “No Limit” or a percentage less than 

the source capacity.

The Target Tolerance menu item displays the current setting in parentheses. 

Default is “No Limit.”

NOTE:

 The size of the file system on the source is always duplicated with all 

contents. Target devices greater than or less than the source capacity will 

not reflect any changes to correct the difference.

Содержание UDFH7









Отзывы: