ADC Campus-REX2 RS Скачать руководство пользователя страница 67

Страница: 67 / 166

Chapter 3 - Configuring the REX2

Campus-REX2 RS Interface Card User Manual

If you are only changing DHCP configuration, go to

“Saving the Router

Configuration” on page 55

to save your changes.

Saving the Router Configuration

Type

and press

until you return to the REX2 Configuration

and Status screen (

page 3-30

Type

to save changes. The following message is displayed to show

that the save in progress:

WARNING: Do not power off unit or remove LAN

or Line connection.

Saving REX2 configuration; Please wait...

The following message is displayed when the save is completed:

REX2 configuration saved

Hit Any Key to Continue

Do not remove power to the Campus unit or disconnect the
Line and LAN side network connections when upgrading
software or saving configuration.

ENTER

Jul 07, 2003

ADC TELECOMMUNICATIONS, CAMPUS RS, Version 5.1 08:19:34

Local Unit ID:

Local I/F:

REX2

Remote Unit ID:

Remote I/F: REX2

Circuit ID:

REX2 CONFIGURATION AND STATUS

LAN STATUS:

100BaseT, Full Duplex, Up

LINE STATUS:

Standard, Auto, T1, Down

MAC ADDRESS:

00:20:A7:01:02:08

1) Network Protocol:

Router

(Bridge, Router)

2) Encapsulation:

cHDLC

(cHDLC, PPP)

3) Timing Source:

Internal

(Internal, HDSL)

4) ROUTER CONFIGURATION

5) ROUTER STATISTICS

6) SNMP CONFIGURATION

7) SAVE REX2 CONFIGURATION

WARNING:

Configuration change(s) will be lost if not saved before

resetting or powering unit down.

(R)eturn

ENTER CHOICE>

Содержание Campus-REX2 RS







































































































































































Результаты поиска

Содержание Campus-REX2 RS

Отзывы:

Бренды по названию

Популярные бренды

ADC Campus-REX2 RS, Руководство пользователя

Результаты поиска

Содержание Campus-REX2 RS

Отзывы:

Бренды по названию

Популярные бренды