ADB L-852A Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 58

background image

© ADB Airfield Solutions All Rights Reserved

17

2.3.5 Torquing and

Installation Guidance for

In-pavement Fixtures

In-pavement fixtures must be installed according to the plans and specifications; the
applicable regulatory guidance; and the following guidance. The importance of using the
proper fixture clamping components and bolt torque to minimize the risk for fixture failure or
loosening of clamping components cannot be overemphasized. Refer to “Appendix A” on
page 25 for torque and installation guidelines for this fixture.

2.3.5.1 Installation on a Shallow

Base

Installing the F-Range light fixture on a shallow base involves preparing the pavement recess
and wireways, then installing the light fixture on a shallow base.

See FAA AC 150/5345-30 and the project site-specific plans and specifications for details on
shallow base installation.

Also follow the applicable instructions in the previous section, when connecting, installing and
powering the fixture.

Figure 6:

Example of a Shallow Base Installation

WARNING

Read installation instructions in their entirety before starting installation.
• Failure to follow the installation guidance could result in bolt loosening or bolts breaking off,

resulting in catastrophic failure of the fixture and/or the mounting system components.

Failure to follow these warnings may result in serious injury or
equipment damage.

1-1/2" (TYP.)

L868B FLANGE RING 12.25" O.D.
3/4" THICK, 5402/12Y
WITH O-RING GASKET (TYP.)

SEMI-FLUSH
LIGHT FIXTURE

TYPE L-85X (TYP.)

NORDLOCK NL 3/8 2 PIECE

3/8-16 STAINLESS STEEL BOLT

(TYP. OF 6)

0.75"

GROUND WIRE

6 AWG OR LARGER

L868B LIGHT BASE

L-823 PRIMARY CONNECTOR

L868B SPACER RING(S)

GROMMET

2" PVC CONDUIT W/BELL END

3/4" DRAIN HOLE (CENTERED)

FIXTURE TOP EDGE TO BE

+0/-

1

16 " BELOW GRADE

Earth Ground

L-823 PRIMARY EXTENSION

GROMMET

ISOLATION TRANSFORMER
(max 3 per can)

L-823 SECONDARY CONNECTOR

Earth Ground

LOCKWASHER OR EQUAL

L868B LIGHT BASE

Earth Ground

3/4" DRAIN HOLE (CENTERED)
(if used)

L868B SPACER RING(S)

L868B FLANGE PLATE 12.25" O.D.

L868B JUNCTION HOUSING

See “Installation on L-868 Base” on page 16

«
...
21
22
23
24
25
...
»

Содержание L-852A



























































Отзывы:

Нет отзывов

Похожие инструкции для L-852A

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: JB-Lighting Страницы: 60

Бренд: ACCU-CHECK Страницы: 104

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Ocmis Irrigazione Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды