ADB Safegate RELIANCE Omni 1-Dome Скачать руководство пользователя страница 39

Страница: 39 / 66

6. Apply one drop of Loctite 234 and tighten the four M5x10 screws crosswise using a torx key set to 3.5 mm to a torque of

3.5 Nm.

7. Check the light fixture for water-tightness.

Note

Refer to

Checking the Light Fixture for Water-tightness

section for more information.

6.4.7 Closing and Testing Light Assembly

To close and test the light assembly, perform the following procedure:

CAUTION

Misalignment of the index pin in the inner cover flange and its mating hole in the underside of the top cover and will

prevent components from being assembled correctly. Damage may also occur to the top cover and inner cover.
Failure to follow this instruction can result in equipment damage.

1. See

Figure 12

Turn the cover over and find the arrow cast into the top of the cover. This arrow indicates the location of the index pin

hole that is machined into the underside area of the top cover.

2. See

Figure 13

Find index pin molded into the flange of the inner cover. The index pin needs to align with its mating hole found on the

underside of the top cover.

Figure 12: Index Pin Hole Arrow

Figure 13: Index Pin of Inner Cover Flange

3. Put the top cover over the inner cover and align the index pin on the inner cover flange with the index arrow on the top

cover

4. Gently put the inner cover on top of the cover (

Figure 12

), taking into account the index pin between both parts.

Make sure that LED leads do not get damaged when the top cover is installed on the inner cover.

5. Press the inner cover on the cover and secure with new torx head screws with washers.

UM-5073, Rev. 1.0, 2021/07/13

Содержание RELIANCE Omni 1-Dome


























































Результаты поиска

Содержание RELIANCE Omni 1-Dome

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE Omni 1-Dome, Руководство пользователя

Результаты поиска

Содержание RELIANCE Omni 1-Dome

Отзывы:

Бренды по названию

Популярные бренды