ADB Safegate RELIANCE L-810 OBSL-L Скачать руководство пользователя страница 29

Страница: 29 / 34

Figure 6: Glassware Assembly Parts

44A7668/

X X X X X

(DIGIT 1)COLOR

OBSTRUCTION LIGHT RED, FAA = 1

OBSTRUCTION LIGHT RED, ICAO TYPE A & B, CANADA = 2

(DIGIT 2) RED/IR

RED ONLY = 0

RED & IR = 1

(DIGIT 3) FLASH

WITHOUT FLASH = 0

WITH FLASH = 1

(DIGIT 4) RESERVED = 0

(DIGIT 5) ARCTIC KIT

WITHOUT ARCTIC KIT = 0

WITH ARCTIC KIT = 1

62A2265

EMIL LENS DOOR

63A1117/X

ELIL GLASSWARE

63A1279

SEAL: SIDE EMITTING LED LENS

44A7614/XXXX

OBSL W-IR LIGHT ENGINE ASSEMBLY

64A1067/06

M3 X .5 X 6 FLAT HD TORX 90 DEG

1. SECURE M3 FASTENERS WITH MEDIUM STRENGTH LOCTITE 242.

Table 4: LED Light Engine Order Code

44A7614/

IR Content

0 - Red Visible Light Only

1 - Red and IR

Flash Option

0 - Without Flash

1 - With Flash

Not Used (0)

Arctic Kit (Heater, 120 Vac Only)

0 - Without Arctic Kit

1 - With Arctic Kit (120 Vac

Only)

96A0476, Rev. F, 2019/12/12

Содержание RELIANCE L-810 OBSL-L





























Результаты поиска

Содержание RELIANCE L-810 OBSL-L

Отзывы:

Похожие инструкции для RELIANCE L-810 OBSL-L

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE L-810 OBSL-L, Руководство пользователя

Результаты поиска

Содержание RELIANCE L-810 OBSL-L

Отзывы:

Похожие инструкции для RELIANCE L-810 OBSL-L

Бренды по названию

Популярные бренды