manualshive.com logo in svg

ADB Safegate RELIANCE Gate Sign, Руководство пользователя

Поделиться
Скачать
ADB Safegate RELIANCE Gate Sign Скачать руководство пользователя страница 45

Figure 29: Converter

B

C

D

E

3. Remove the center screw (C) holding the terminal block to release the converter earthing wire. See 

Figure 29

.

4. Remove the grey LED cable (D) from the adapter card. See 

Figure 29

.

5. Remove the two screws (E) attaching the converter to the electronics box. See 

Figure 29

.

6. Remove the old converter from the electronics box, then attach the new one using the two screws (E). See 

Figure 29

.

7. Attach the earthing cables under the terminal block using the center screw (C). See 

Figure 29

.

8. Attach the two black wires form the converter to the two upper right screws (B) of the terminal block. See 

Figure 29

.

9. Attach the grey LED cable (D), with the colored wires to the right, to the adapter card and the B-channel. See 

Figure 29

.

10. Close and attach the lid to the box using the six countersunk screws (A). See 

Figure 28

.

UM-4007, Rev. 6.0, 2022/07/18

39

Copyright 

©

 ADB Safegate, All Rights Reserved

Содержание RELIANCE Gate Sign











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды