ADB Safegate RELIANCE Gate Sign Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 74

background image

7. On the front, mount the washers and lock nuts.

Figure 13: Attach washers and tighten lock nuts

8. Gently tighten the lock nuts, using a wrench to keep the eye bolt fixed.
9. Fasten the tethering wire bracket to the mounting base of the pole or in the foundation.

4.3.2 Tether Wire - with pre-drilled Holes

The sign should always be secured using the supplied tether wire. There are two positions prepared for tether wire

installation. These are located on the bottom frame and 300 mm from the edge of the sign on each side.
Choose which of the prepared tether wire locations to use based on the sign’s specific installation site
Before you start, make sure that the sign is unpowered.
Tools to use

•

Wrench

Installation

1. Choose which of the prepared tether wire locations to use based on the sign’s specific installation site.
2. Place the bracket on the lower frame.

Figure 14: Place the bracket

UM-4007, Rev. 6.0, 2022/07/18

23

Copyright

©

ADB Safegate, All Rights Reserved

«
...
27
28
29
30
31
...
»

Содержание RELIANCE Gate Sign











































































Отзывы:

Нет отзывов

Похожие инструкции для RELIANCE Gate Sign

Бренд: Daewoo Страницы: 62

Бренд: C2STek Страницы: 8

Бренд: SkyGuard Страницы: 6

Бренд: I-gotU Страницы: 17

Бренд: SunTech Страницы: 30

Бренд: Navman Страницы: 42

Бренд: Garmin Страницы: 48

Бренд: Garmin Страницы: 40

Бренд: Garmin Страницы: 67

Бренд: StarGPS Страницы: 29

Бренд: Microsport Страницы: 27

Бренд: Mongoose Страницы: 16

Бренд: Mongoose Страницы: 16

Бренд: Garmin Страницы: 2

SmartBeacon-4AA Pro

Бренд: SENSORO Страницы: 13

Бренд: OzSpy Страницы: 19

Бренд: Franklin Страницы: 11

Бренд: RedKnows Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды