ADB Safegate RELIANCE AC Скачать руководство пользователя | Manualshive

Страница: 43 / 56

background image

Note

Make sure that light fixtures with only one LED-cable is connected to the LED B-channel.

Figure 23: Converter with 1 connector

Figure 24: Converter with 2 connectors

3. Assemble the light fixture.

6.2.6 Reset the Fail Open converter 2.3

Open

1. Disconnect and disassemble the light fixture.
2. Make sure you have a 2-way electrical shunt/jumper (2.54 mm/0.100

‑

inch spacing), see

.

Figure 25: 2-way electrical shunt/jumper

Reset

1. Locate the 3-pin reset connector(s) on the converter. For the two-connector converter, there is one reset connector for

each side.

2. Place the 2-way electrical shunt (2.54 mm spacing) over the two pins marked red, see

.

Figure 26: Converter with 1 connector

Figure 27: Converter with 2 connectors

3. Close the light fixture and connect it to a CCR.

UM-0210, Rev. 2.0, 2020/04/30

33

Copyright

©

ADB Safegate, All Rights Reserved

«
...
41
42
43
44
45
...
»

Содержание RELIANCE AC

























































Отзывы:

Нет отзывов

Похожие инструкции для RELIANCE AC

Бренд: RAB Страницы: 2

Бренд: HANYOUNG NUX Страницы: 2

Robus RVB007RGB10I65

Бренд: LED Group Страницы: 2

ECO POOL 006-527-6316 Series

Бренд: Paramount Fitness Страницы: 8

Бренд: RAB Lighting Страницы: 2

Бренд: SKF Страницы: 65

Бренд: Cello Страницы: 12

Cooper Lighting XNV2

Бренд: Eaton Страницы: 6

WASH 250 Series

Бренд: Silver Star Страницы: 18

Бренд: JONATHAN Y Страницы: 2

Бренд: Barco Страницы: 70

Бренд: Patriot Lighting Страницы: 2

Бренд: Luminaire led Страницы: 3

Бренд: Emos Страницы: 24

EPL-120-150-EPP

Бренд: Larson Electronics Страницы: 4

Varyscan 4 1200HMI

Бренд: JB-Lighting Страницы: 48

CHARLSON TBL4126A

Бренд: Safavieh Lighting Страницы: 2

Бренд: Lampo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды