ADB Safegate RELIANCE AC Скачать руководство пользователя | Manualshive

Страница: 12 / 56

background image

1.1.1 Introduction to Safety

CAUTION

Unsafe Equipment Use

This equipment may contain electrostatic devices, hazardous voltages and sharp edges on components

• Read installation instructions in their entirety before starting installation.
• Become familiar with the general safety instructions in this section of the manual before installing,

operating, maintaining or repairing this equipment.

• Read and carefully follow the instructions throughout this manual for performing specific tasks and

working with specific equipment.

• Make this manual available to personnel installing, operating, maintaining or repairing this

equipment.

• Follow all applicable safety procedures required by your company, industry standards and

government or other regulatory agencies.

• Install all electrical connections to local code.
• Use only electrical wire of sufficient gauge and insulation to handle the rated current demand. All

wiring must meet local codes.

• Route electrical wiring along a protected path. Make sure they will not be damaged by moving

equipment.

• Protect components from damage, wear, and harsh environment conditions.
• Allow ample room for maintenance, panel accessibility, and cover removal.
• Protect equipment with safety devices as specified by applicable safety regulations
• If safety devices must be removed for installation, install them immediately after the work is

completed and check them for proper functioning prior to returning power to the circuit.

Failure to follow this instruction can result in serious injury or equipment damage

Additional Reference Materials

Important Information

•

IEC - International Standards and Conformity Assessment for all electrical, electronic and related technologies.

•

IEC 60364 - Electrical Installations in Buildings.

•

FAA Advisory: AC 150/5340-26 (current edition), Maintenance of Airport Visual Aid Facilities.

•

Maintenance personnel must refer to the maintenance procedure described in the ICAO Airport Services Manual,

Part 9.

•

ANSI/NFPA 79, Electrical Standards for Metalworking Machine Tools.

•

National and local electrical codes and standards.

1.1.2 Intended Use

CAUTION

Use this equipment as intended by the manufacturer

This equipment is designed to perform a specific function, do not use this equipment for other purposes

• Using this equipment in ways other than described in this manual may result in personal injury, death

or property and equipment damage. Use this equipment only as described in this manual.

Failure to follow this instruction can result in serious injury or equipment damage

RELIANCE Inset Lights
Safety

2
Copyright

©

ADB Safegate, All Rights Reserved

«
...
10
11
12
13
14
...
»

Содержание RELIANCE AC

























































Отзывы:

Нет отзывов

Похожие инструкции для RELIANCE AC

Бренд: iGuzzini Страницы: 20

AtLite Sure-Lites SELDWA29SD

Бренд: Eaton Страницы: 4

Бренд: ADJ Страницы: 6

LIGHT LINEAR PT 1

Бренд: LIGMAN Страницы: 6

Бренд: Ikan Страницы: 5

Бренд: Heitronic Страницы: 16

HALD-48-1X4-2X50LED

Бренд: Larson Electronics Страницы: 2

NAUTICA WL ROUND CHROME

Бренд: Qazqa Страницы: 2

Бренд: FAAC Страницы: 2

Бренд: A&A Manufacturing Страницы: 10

EPL-HB-150LED-RT-140DB-JB3

Бренд: Larson Electronics Страницы: 3

Бренд: NEO TOOLS Страницы: 7

ASTRO-MOBILE-SOUND

Бренд: Party Light & Sound Страницы: 2

Бренд: Lumatek Страницы: 44

Бренд: Vagner Pool Страницы: 32

Бренд: Graci-lite Страницы: 2

Бренд: Oase Страницы: 16

HL-85-LED-CPR-30-TRP

Бренд: Larson Electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды