background image

10.  ADVANCED FEATURES

In addition to the standard features there are some advanced features available mainly for 

trouble shooting. 

To enter the Advanced Feature mode, turn the unit ON and press the programming button five 

(5) times before the intensity number blinks.  First an “A” will appear on the left digit and a 

number on the right.   Press the programming button until the appropriate number is shown for 

that slot.  Wait for a “B” to appear and repeat this for “C” and “D” as well.  This will put you into 

that mode until the unit is turned off and back on again.  See below a list of codes and slots for 

these advanced features. 

A

 

B

 

C

 

9

 

9

 

6

 

9

 

Minimum Speed Mode 

Alternate Slow Down Mode 

Demo mode (see further instructions) 

Show Serial Number 

Display Diagnostic Mode 

Auto Intensity Diagnostic Mode 

Turn On & Off   Radar Acceleration Filter 

Turn On & Off   No Display Availability 

Turn On & Off   Set Time Availability 

Minimum Speed Mode 

Lower speeds of 5 mph are distracting in most applications but are desirable in some.  As a 

default, the display will only show down to 5 mph but down to 1 mph is available.  Putting in 

the minimum speed code will turn on and off the down to one mode.   If after putting in the 

minimum speed code, the display shows “S1” then the speed will show down to 1 mph.   If “S5” 

shows then the speed will only show down to 5 mph. 

Alternate Slow Down Mode 

The display can show the “Slow Down” violator alert two ways.  One is that only “Slow Down” is 

shown if the vehicle speed is over that set speed.  The other is that the “Slow Down” will show 

and then the vehicle speed will display, alternating between the two until the vehicle slows 

below the set speed.  Both are very effective but one could be preferred above the other.  The 

default is just “Slow Down”.  To switch from one or the other, put in the code and if the display 

shows “On” then only the “Slow Down” message will display.  If after the code is put in and “Off” 

shows then the display will alternate between “Slow Down” and their speed.  

Demo Mode 

Demo Mode will allow you to select 1 of 6 Demo.   The display will show DM for Demo Mode 

and then a number.   Change the number to the desired demo. Please note the sign when 

turned off will not turn on back on Demo Mode, but normal operating mode. 

1 = Counts up and down from 51 to 59 and flashes 

       Demonstrates Dimming Feature 

       Shows “Slow Down” Violator Alert

       Shows “Red and Blue” Violator Alert 
2 = Shows just “Slow Down” Violator Alert 

3 = Shows just “Red & Blue” Violator Alert 

4 = Counts up and down from 31 to 39 flashes 

Содержание FAST 350





















Отзывы: