background image

1-4

 A

LPHA 

4000 R

G

B NEMA 12, I

NSTALLATION 

M

ANUAL 

(PN 1778600401 R

EV

B

)

I

NTRODUCTION

Alpha 4000 R

G

B

 NEMA 12

Introduction

Item

Name

Description

Item

Name

Description

A

CEILING MOUNT 

ATTACHMENT 

POINTS

Optional ceiling mount. 

Attach provided hanging 

brackets here.

G

COMMUNICATION 

ENTRY POINT

1/2 inch trade size hole (.875") 

for communication wiring entry. 

B

MICRO SD 

CARD ACCESS 

PANEL

Removable panel to access 

micro SD card.

H

C

REAR BRACKET

MOUNT 

Attach wall mounting brackets 

at this location.

I

POWER ENTRY

POINT 

CABLE TIE WRAP

MOUNT

Tie wrap mount for cable 

management (if needed).

D

REAR

COMMUNICATION

ACCESS PANEL

Removable panel to 

access RS232, RS485, or 

Ethernet communication 

input connections.

D

C

C

A

B

J

Top View

Back View

Bottom View

F

F

E

H

G

I

K

E

REAR POWER

ACCESS PANEL

Removable panel to access

120-240VAC power input

connection.

REAR ACCESS

PANEL SCREWS 

8-32 Phillips screws. Take 

care not to lose screws.

1/2 inch trade size hole (.875") 

for AC power wiring entry. 

Alternative 1/2 inch trade size 

holes (.875") for communication 

wiring with removable water tight 

plug (if used replace into rear 

communication entry point (G)).

J

ALTERNATIVE

COMMUNICATION

ENTRY POINT

Alternative 1/2 inch trade size 

holes (.875") for power wiring 

with removable water tight plug 

(if used replace into rear power 

entry point (H)).

K

F

ALTERNATIVE 

POWER ENTRY 

POINT

The Alpha 4000RGB NEMA 12 displays are full color Industrial grade displays designed to NEMA 12/IP52 standards 

which are intended for indoor use only. Performance scoreboards communicate critical information to Production 

Operators and Managers for an effective productivity improvement program, ensuring KPIs are met, eliminating waste 

and increasing productivity. Factory floor displays are proven tools for displaying useful, accurate, current & visible 

production measurements, allowing production teams to focus on continuously improving production performance. NEMA 

12 displays provide protection against falling dirt and circulating dust and light splashing water making them the right 

choice for the plant floor.

Sign overview

Содержание Alpha 4000 RGB NEMA 12














Отзывы: