background image

8-9

Installing ATM Software for Novell NetWare

47007900000000000000000000

00a03e00000100

Signalling 
ATM 
Adaptation 
layer version 
number

30

30, 31

Specifies the ATM 
signaling adaptation 
layer, or QSAAL 
version number.

Signalling 
Stack version 
number

30

30, 31

Specifies the ATM 
signaling stack, or Q93B 
version number.

Want to 
Specify 
LES_ADDR?

no

no, yes

Specifies if the LEC has 
to register directly to 
the LES.

LECS 
Address 
(Network Port)

1

Well-

known 
LECS 
address

Network 
NSAP; up 
to 26 
characters

Specifies the first 13-
byte network portion 
of the NSAP address for 
the LECS.

LECS 
Address (ESI 
Port)

2

Well-

known 
LECS 
address

ESI 
NSAP; up 
to 14 
characters

Specifies the last 7-byte 
end system identifier 
(ESI) portion of the 
NSAP address for the 
LECS.

LES Address 
(Network Port)

Network 
NSAP; up 
to 26 
characters

Specifies the first 13-
byte network portion 
of the NSAP address for 
the LES.

LES Address 
(ESI Port)

ESI 
NSAP; up 
to 14 
characters

Specifies the last 7-byte 
ESI portion of the NSAP 
address for the LES.

ELAN Name

default

Up to 25 
characters

Specifies the ELAN 
name for the LES.

Parameter

Default 
Value

Possible 
Values

Description

Содержание 5ANA-940

























































































































































Отзывы: