2
3
IMPORTANT SAFETY AND MOUNTING INSTRUCTIONS
→ Before installation, read and follow the safety and mounting instructions contained herein.
→ Due to any work at heights, the weight of speakers, technical training, know-how and
experience as well as knowledge of relevant provisions, regulations and standards needed to
mount speakers, mounting brackets must be installed by specialists who are able to assess
the task, recognize potential hazards and ensure appropriate safety measures are taken. The
following safety and mounting instructions are addressed to this specialist.
→ At least two people are required to mount any speaker. When necessary, the loudspeaker
should be held by the second specialist. In some circumstances an additional method of
supporting the loudspeaker may be required.
→ When mounting, observe and follow any relevant local, national and international regulations
and standards.
→ Also read and follow the installation instructions contained in the operating manual of the
mounted loudspeaker and any third-party mounting hardware.
→ Keep these instructions and include them when transferring this mounting hardware to third
parties.
→ Do not install this mounting hardware in locations where it will be exposed to externally
generated vibrations.
→ This mounting hardware must only be fastened above or below the loudspeaker cabinet, i.e.
not on the sides, front or rear.
→ This mounting plate should only be used with specified loudspeaker models and no additional
objects should be supported by this mounting plate.
→ Only combine ADAM Audio mounting hardware, third party brackets/stands, or loudspeakers
as shown in the “Hardware Mounting Matrix” which can be found on www.adam-audio.
com. Other manufacturers’ mounting brackets may also work but we do not guarantee that.
The quality and compatibility of third-party hardware is the responsibility of the respective
supplier.
→ There is a danger that the loudspeaker and mounting hardware may drop until the mounting
has been fully completed.
→ Ensure that the fully assembled adapter plate and loudspeaker is mounted so that the center
of gravity is centered. Any leverage that may be present should be minimized and this must be
especially considered when tilting the loudspeaker.
→ Particularly when mounting a loudspeaker overhead, use safety wires (or equivalent) to
prevent the loudspeaker and the mounting hardware from dropping or tipping. Used safety
devices must be appropriately specified for the attached load, not have any damage, and
conform to local regulations and standards. If a safety wire has prevented tipping or dropping,
it should be replaced with a new one. ADAM Audio does not supply safety wires.
→ Every three months check that all the screws are still properly tightened throughout the
complete loudspeaker / mounting plate / stand or bracket assembly. Also check that safety
wires (or equivalent) are still in “as new” condition.
→ Dismount the loudspeaker if there is any damage to the mounting hardware/loudspeaker or
deviation from safety and mounting instructions.
Weight
1.21 kg (2 lbs 11 oz)
Dimensions (H x W x D)
150 mm x 150 mm x 5 mm (accurate)
5 7/8“ x 5 7/8“ x 3/16“ (approximate)
Maximum load
40 kg (88 lbs 3 oz)
PACKAGE CONTENTS
Reference
Description
Quantity
A
150 mm x 150 mm x 5 mm Universal Mounting Plate
1
B
Contersunk head screw ISO 10642 - M6 x 16 mm - black
2
C
Hexagon nut DIN 985 - M6 - galvanized
2
D
Contersunk head screw ISO 10642 - M8 x 20 mm - black
2
E
Hexagon nut DIN 985 - M8 - galvanized
2
F
Spacer Ø18 mm x Ø8,4 mm x 12 mm - Polyamid - black
4
G
Hexagon socket button head screws ISO 7380 M8 x 35 mm - black
4
H
Spacer Ø18 mm x Ø8,4 mm x 4 mm - Polyamid - black
4
I
Washer DIN 125 - Ø17 mm x 8,4 mm x 1,6 mm - black
4
EN
EN
A
B
G
F
C
E
D
I
H
