Adam Hall GmbH · Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany
Tel.: (+49) 60 81 / 94 19 0 · Fax: (+49) 60 81 / 94 19 1000 · eMail: [email protected]
4
6
7
6
8
9
3
1
2
5
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain
that wall mounts are properly installed and secured. Make certain that the equipment is installed securely
and cannot fall down.
7. During installation, observe the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat.
Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment
- in this case, observe the special instructions noted below. Do not expose this equipment to flammable
materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled
with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to
tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property damage
and personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or
if it has been damaged in another way, switch it off immediately and unplug it from the mains outlet (if it
is a powered device). This equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:
22. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do
not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on
the equipment until it has reached room temperature.
23. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency
match the values specified on the equipment. If the equipment has a voltage selection switch, connect
the equipment to the power outlet only if the equipment values and the mains power values match. If the
included power cord or power adapter does not fit in your wall outlet, contact your electrician.
24. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at
the mains outlet and/or power adapter and the equipment connector.
25. When connecting the equipment, make certain that the power cord or power adapter is always freely
accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if
you want to clean the equipment. Always unplug the power cord and power adapter from the power outlet
at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter
with wet hands.
26. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this
can shorten the useful life of the equipment.
27. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter
from the power outlet.
28. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or
before extended periods of disuse.
Important:
Before installation, check that all installation kit components are complete, undamaged and work
correctly (e.g. bolts, nuts, locking pins, threads in speakers, etc.). Should any installation kit component be
damaged, missing or not function properly, the installation kit should not be used. Pay attention to the maxi-
mum load of all components. During installation, attach a suitable secondary safety component if necessary.
Overhead mounting requires extensive experience, including the calculation of the load limit values of the
installation material and regular safety inspection of all installation materials and devices, such as lights and
speakers. If you do not have these qualifications, do not attempt to perform an installation yourself. Refer
instead to a qualified professional.
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at: https://cdn-shop.adamhall.com/me-
dia/pdf/Manufacturers-Declarations-AD_DE_EN_ES_FR.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1,
61267 Neu Anspach / Email [email protected] / 49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not
be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled
waste disposal. Please dispose of this product separately from other waste and have it recycled to promote
sustainable economic activity.
SUPER CLAMP B SET 1
Universal Haken mit Knauf schwarz und Bolzen SS018
Artikelnummer:
SCP710BSET1
Product type:
Truss Accessories
Components:
Universal clamp SCP710B mounting pin SS018
Weight:
0.544 kg
Universal clamp SCP710B
Type:
Universal clamp
Material:
Die-cast aluminium
Finish:
Powder coated
Colour:
Black
Suitable for tubing
diameter:
13-55 mm
Flange:
For mounting pin SS017 or SS018
Weight:
0.48 kg
INTRODUCTION
The SCP710BSET1 mounting kit comprises the universal clamp SCP710B and the mounting pin SS018, and
is suitable for secure mounting of lights, speakers and other devices to traverses and tripods.
PART DESCRIPTION
1
Adjustable clamping lever for attaching the universal clamp.
2
M6 T-screw for securing the mounting pin.
3
Mounting pin with M10 thread and M10 wing nut.
4
Flange for mounting bolt.
5
Spring-loaded locking pin.
6
M5 thread
7
M6 thread
8
Clamp opening (adjustable from 13 to 55 mm).
9
Plastic adapter for mounting on a square tube. Insert the wedge-shaped adapter into the 90° angled
recess of the upper clamp jaw.
MOUNTING
• Attach a device suitable for traverse mounting to the mounting pin (No. 3) with the M10 wing nut.
• Mount the universal clamp on a traverse or stand in a suitable position using the adjustable clamp lever
(No.1) and ensure a firm grip.
• Loosen the locking screw (No.2) so far that the flange (No.4) on the underside of the clamp can accept the
mounting pin (No.3) (do not remove the bolt).
• Push the spring-loaded locking pin (No.5) on the side of the clamp into the housing so that the flange
(No.4) on the underside of the clamp can accept the mounting pin and push the pin all the way into the flange.
• Release the pressure from the locking pin and keep hold of the device being mounted until you are certain
that the mounting pin is fully engaged.
• Rotate the device to achieve the desired dispersion and secure the connection by tightening the lockin
screw (No. 7).
When mounting devices to traverses and stands, pay attention to the information in the safety instructions in
this manual, and in particular the information under ‘
Important
’.
Safe working load
(SWL):
20 kg
Additional features:
TÜV-certified
Mounting pin SS018
Type:
Mounting pin for universal clamp
Material:
Brass
Finish:
Unfinished
Thread:
M10 x 16
Weight:
0.064 kg
Additional features:
M10 wing nut included
SPECIFICATIONS
