PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.
3
2
Install or Replace Batteries
AcuRite recommends high quality
alkaline batteries in the sensor for
the best product performance.
Heavy duty or rechargeable
batteries are not recommended.
1. Slide off the battery compartment
cover.
2. Insert 2 x AAA batteries into the
battery compartment, as shown.
Follow the polarity (+/-) diagram
in the battery compartment.
3. Replace the battery cover.
Set the A-B-C Channel
The A-B-C button is located on the
back of the sensor, above the battery
compartment. Press and release to
set channel to A, B or C (shown on
the sensor display’s channel
indicator).
NOTE:
If being used with a
companion product that has an
A-B-C channel, you must select the
same letter choice for both the
sensor and the product it is being
paired with in order for the units to
synchronize.
1
2
SETUP
Specifications
TEMPERATURE RANGE:
-4°F to 158°F; -20°C to 70°C
HUMIDITY RANGE:
1% – 99% RH (relative humidity)
BATTERY REQUIREMENTS:
2 x AAA alkaline
WIRELESS RANGE
330
ft
/ 100 m depending on home construction materials
OPERATING FREQUENCY
433
.92
MHz
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement
of the sensor is critical to the accuracy and performance of this product.
Sensor Placement
The sensor is designed for indoor use. Place the sensor in a dry area
free of dirt and dust. Sensor stands upright for tabletop use and is
wall-mountable.
Important Placement Guidelines
• To ensure accurate temperature measurement, place sensor out of direct sunlight
and away from any heat sources.
• Sensor must be within 330 ft (100 m) of companion unit (not included).
• To maximize wireless range, place sensor away from large metallic items, thick
walls, metal surfaces, or other objects that may limit wireless communication.
• To prevent wireless interference, place sensor at least 3 ft (0.9 m) away from
electronic devices (TV, computer, microwave, radio, etc.).
For more information, visit our Knowledge Base at http://www.AcuRite.com/kbase
2
A-B-C Channel
Install Batteries
2 AAA Batteries
1
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.