Active AGi2100, Руководство пользователя

Страница: 69 / 200

69
AGi2100
Inverter
50
230
1.8
1.6
1.0
ISO8528 G2
≤5
12 - 8.3
DC Non-fuse Protector
AC Control by inverter overload
protect program
LC148F./
Single cylinder, 4-Stroke,
forced air cooling, OHV
79
Unleaded Gasoline
4
0.35
E6TC E6RTC
Recoil start
Generator 499×285×455
set 21
63.5
MODEL
Generator
Type
Rated frequency/Hz *
Rated voltage/V *
Max. output power/kW
Power factor
AC output quality
THD/%
Noise Level dB/LpA/LwA/K 4m
(3/4 load)
DC Output/ V-A
Overload protect
Engine
Engine
Engine type
Displacement/cc
Fuel type
Fuel capacity/L
Continue Running
Time (at rated power) / h
Net weight/kg
4
Oil Capacity/L
Spark Model No.
Starting mode
Length×Width×Height/mm
8. PERIODIC MAINTENANCE:
The spark plug is an important
engine component which
should be checked periodically.
1 . Remove the cap
①
and spark
plug cap
②
.
2 . Insert the handlebar
③
into
the tool
④
and turn it
counterclockwise to remove the
spark plug.
3. Check for discoloration and
remove any carbon deposits.
The porcelain insulator around
the center electrode of the spark
plug should be a medium to
light tan color.
4. Check the spark plug type
and gap.
Standard Spark Plug:
E6TC E6RTC
BP6HS / BPR6HS (NGK)
L87YC /R L87YC (CHAMPION)
W16FP / W16FPR (DENSO)
W6BC / WR6BC (BOSCH)
If needing EMC Certification,
engine must use E6RTC spark
plug.
Spark Plug Gap:
0,6-0,7mm
TIP:
The spark plug gap should be
measured with a wire thickness
gauge and, if necessary, adjust.
5. Install the spark plug.
Spark Plug Torque: 20.0 Nm.
6. Install the spark plug cap and
spark plug cover.
Spark plug inspection
TIP:
If a torque wrench is not available when installing a spark plug; a good estimate of
the correct torque is 1/4-1/2 turn past finger tight. However, the spark plug should
be tightened to the specified torque as soon as possible.
AGi2100
Inverter
50
230
1.8
1.6
1.0
ISO8528 G2
≤5
12 - 8.3
DC Non-fuse Protector
AC Control by inverter overload
protect program
LC148F./
Single cylinder, 4-Stroke,
forced air cooling, OHV
79
Unleaded Gasoline
4
0.35
E6TC E6RTC
Recoil start
Generator 499×285×455
set 21
63.5
MODEL
Generator
Type
Rated frequency/Hz *
Rated voltage/V *
Max. output power/kW
Power factor
AC output quality
THD/%
Noise Level dB/LpA/LwA/K 4m
(3/4 load)
DC Output/ V-A
Overload protect
Engine
Engine
Engine type
Displacement/cc
Fuel type
Fuel capacity/L
Continue Running
Time (at rated power) / h
Net weight/kg
4
Oil Capacity/L
Spark Model No.
Starting mode
Length×Width×Height/mm
8. PERIODIC MAINTENANCE:
Carburetor settings
The carburetor is a vital part of the engine. Adjusting should be left to an authorized
dealer or those with professional training and equipment to do so properly.
Engine oil replacement
Avoid draining the engine oil immediately after stopping the engine. The oil may
be hot and should be handled with care to avoid burns.
WARNING:
1
. Place the generator on a level
surface and warm up the engine
for several minutes. Stop the
engine and turn the 3 in 1
switch knob and fuel tank cap
air vent knob to “OFF”.
2
. Remove the screws
①
and
then remove the cover
②
.
3 . Remove the oil filler cap
③
.
4 . Place an oil pan under the
engine. Tilt the generator to
drain the oil completely.
5 . Replace the generator to a
level surface.
Do not tilt the generator when
adding engine oil. This could
result in overfilling and
damage to the engine.
6 . Add engine oil to the upper
level.
Recommended engine oil:
SAE 10W -30
Recommended engine oil grade:
API Service SE type or higher
Engine oil quantity:
0.35 L
7 . Wipe the cover clean, and
wipe up any spilled oil.
Be sure no foreign material
enters the crankcase.
8 . Install the oil filler cap.
9 . Install the cover and tighten
the screws.
NOTICE
NOTICE