background image

 

  Wireless Connectivity Expert 

ACT-IR100S-L and IR100SL-M

 User’s Manual

 

©

 Copyright 2000-2008 ACTiSYS Corp. 

Page 2 of 20 

 

 

Apr. 22, 2008

ACTiSYS Confidential Information 

 

Version 1.2.0.1

 

 

FCC & VCCI Compliance Statement 

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation. 

WARNING-FCC  Regulations state that any unauthorized changes or modifications to this equipment 

not expressly approved by the manufacturer could void the user authority to operate this equipment 

 

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, 

pursuant to Part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will nor occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can 

be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures: 

 

-Increase the separation between the equipment and receiver. 

-Reorient or relocate the receiving antenna. 

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

This equipment is in the 2nd Class category (information equipment to be used in a residential area there 

to) and conforms to the standards set by the Voluntary Control Council For Interference by Data 

Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such 

residential area. 

When used near a radio or TV receiver, it may become the cause of radio interference. Read the 

instructions for correct handling. 

 

NOTE: Must be used with shielded cable only. 

 

FOR YOU RECORDS..... 

For your assistance in reporting this product in case of loss or theft, please record below the model 

number and serial which are located on the bottom of the case. Please retain this information. 

Model Number                    

Serial Number 

Date of Purchase     

Place of Purchase 

 

All indicated copyrights and trademarks in the following pages are copyrights and trademarks of their   

Respective corporations. 

 

Содержание IR100SL





















Отзывы: