background image

 

©

 Copyright 2002-2008 ACTiSYS Corp. 

Page 2 of 21  

Jul 8, 2008

  

Version 

1.6.0.1

 

 

The Wireless Connectivity Expert 

ACT-IR4000US Series

User’s Manual

FCC & VCCI Compliance Statement 

This device complies with part 15 of the FCC Rules. Operation is subject 

to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause undesired operation. 

WARNING-FCC Regulations

 state that any unauthorized changes or modifications 

to this equipment not expressly approved by the manufacturer could void the user 

authority to operate this equipment 

NOTE:

 This equipment has been tested and found to comply with the limits for Class 

B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, 

uses, and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of the 

following measures: 

-Increase the separation between the equipment and receiver. 

-Reorient or relocate the receiving antenna. 

-Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

This equipment is in the 2nd Class category (information equipment to be used in a 

residential area there to) and conforms to the standards set by the Voluntary Control 

Council For Interference by Data Processing Equipment and Electronic Office 

Machines aimed at preventing radio interference in such residential area. 

When used near a radio or TV receiver, it may become the cause of radio interference. 

Read the instructions for correct handling.

 

NOTE: 

Must be used with shielded cable only.

 

FOR YOU RECORDS..... 

For your assistance in reporting this product in case of loss or theft, please record 

below the model number and serial, which are located on the bottom of the case. 

Please retain this information.

 

Model Number 

Serial Number 

Date of Purchase 

Place of Purchase 

All indicated copyrights and trademarks in the following pages are copyrights and 

trademarks of their respective corporations. 

Содержание ACT-IR4000US Series






















Отзывы: