background image

Page 12

© 2009 Active Research Limited

USB Configuration

To communicate with the USG-1, the COM port number 

that Windows has allocated to the USB port needs to be 

determined. The following guide will walk the user through 

this standard operation.

The 

Actisense

  USB  to  Serial  Gateway,  USG-1  is 

completely  USB  port  independent:  it  can  be  easily 

unplugged from one USB port and connected to another 

available USB port on the same PC without the COM Port 

number changing.

To  achieve  this  independent  operation,  plug  the  USG-1 

into  each  required  USB  port  that  you  require  it  to  work 

with in turn, install the USB drivers and manually change 

the allocated COM port number to the same number for 

each USB port. Once configured, the COM port number 

will not change unless instructed to do so by the user.

This is very useful when the USG-1 is working in unison 

with a software program that is set up to use a particular 

COM  port,  as  the  user  does  not  need  to  re  select  a 

different  COM  port  every  time  the  PC  re  boots,  or  the 

cable is swapped between two USB ports.

Step by step guide

1. 

Make  sure  the 

Actisense

  USG-1  is  connected  to  an 

available USB port on the PC. From the Windows ‘

Control 

Panel

’,  open  the  ‘

System  Properties

’  window  and  click 

on the ‘

Hardware

’ tab.

2.

  Click  on  ‘

Device  Manager

’  and  expand  the  ‘

Ports 

(COM & LPT)

’ list by clicking on the ‘

+

’ sign next to it. You 

will find the ‘

Actisense USG’

 in the list, followed by the 

allocated COM port number.

Содержание USG-1-B-485

















Отзывы: