General Safety Information
1. Always carefully read, thoroughly understand and follow the pump operating instructions. Use this pump correctly and with
care for the purpose for which it is intended. Failure to do so may cause damage or personal injury, and will void the
warranty. Please retain instructions for future reference.
2. Contact your chemical or fluid supplier to check for compatibility with pump prior to installation and operation.
3. Prior to use, always carefully and thoroughly read and understand the OSHA information contained in the MSDS sheet
supplied for the chemical which is to be pumped.
4. Wear protective clothing (goggles, face mask, long sleeves, long pants, gloves, aprons, etc) as set forth in the OSHA
Safety Data Sheet when pumping any hazardous chemicals.
5. When using flammable liquids, pump containers should be grounded to avoid static electricity.
6. Any pump used for transferring flammable liquids must be stored in a ventilated area after use.
7. Pump should be washed out before it is used since processing lubricants may contaminate the fluids.
8. Prior to use, inspect your pump thoroughly verifying its proper assembly.
9. If pump is removed from drum, it should be thoroughly rinsed in a liquid that is compatible with the pump.
Operating Instructions & Parts Manual for Model 6008
This pump is designed to fit 5, 15, 30 & 55 gallon drums with 3/4" and 2" threaded openings, and also 2-5/8"
flexspout openings for 5-gallon pails. The extension tubes included can reach the bottom of a 55 gallon
drum. The pump is adjustable to pump 2, 4, 6 or 8 oz per stroke. It has a polypropylene exterior body and polyethylene
internal parts. The pump is commonly used for pumping water, water-based liquids and detergents.
Specifications
Flow rate per stroke. . . . . . . . . . . . . . . . . . . . . . . . . 2, 4, 6 or 8 oz
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 gal. flex 2-5/8"
Inlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"
Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/2"
Bung Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2" & 3/4" PP
Suction Tube (Length & Material). . . . . . . . . . . . . . .32" PE
Packing Gland. . . . . . . . . . . . . . . . . . . . . . . . . . . . . PE
Wetted Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PE & PP
Viscosity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 cps
Max. Temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140°F
Revised 04/01/2004
using hose clamp (Ref. No. 20).
2. Attach discharge spout (Ref. No. 15)
1. Check to see if all parts are present.
Installation
nut.
pump leaks at the top replace packing
Normal maintenance is not required. If
Maintenance
supplier.
compatibility, contact your chemical
fluid. For questions about chemical
compatible with both the pump and
thoroughly in liquid that is
3. If pump is removed from drum, rinse
15) to prevent dripping.
(Ref. No. 16) on end spout (Ref. No.
2. When finished pumping, place cap
leakage.
Tighten only enough to prevent
NOTE:
top of pump.
tighten packing nut (Ref. No. 2) on
If slight leakage should occur, simply
flowing on second or third upstroke.
operation. Liquids should begin
1. The pump is now ready for
Operation
down.
snap off making sure to hold pail
pail, pull towards side of pail and
4. To remove pump with adapter from
snap over the other side.
Insert tube extension into side, then
and remove diaphragm (Ref. B).
3. Remove cap on FLEXSPOUT closure
13). Tightly secure adapter.
threads at bottom of pump (Ref. No.
2. Screw adapter (Ref. No. 14) on male
flexspout closures.
designed to fit senior (metal ring)
1. This adapter (Ref. No. 14) is
PAIL ADAPTER INSTALLATION
spigot.
stand to the side or in back of the
operating the pump, you should
rotated to desired location; when
8. Entire pump head (Ref. No. 4) can be
drum.
No. 18) can be cut to fit specific
7. For various size drums, tubing (Ref.
to limit pump stroke.
(Ref. No. 9 or Ref. No. 11) over rod
top grip (Ref. No. 1) and slide tubing
6. To adjust pump delivery, unscrew
tighten.
5. Insert pump into opening and hand
10).
and secure with hose clamp (Ref. No.
4. Attach extension tubing to (Ref. A)
17) and two clamps (Ref. No. 20).
by using tube connector (Ref. No.
3. Join two lengths of extension tubing
Exploded parts view on reverse side
