manualshive.com logo in svg

ActForNet LEGUANG N900, Руководство по настройке

Поделиться
Скачать
ActForNet LEGUANG N900 Скачать руководство пользователя страница 3

LEGUANG N900 Configuration Guide 

 

                          ActForNet Technologies    Copyright 2014                    

P a g e

 | 

3

 

1. What is included 

 

2. Installation Guide 

2.1 

How to connect  

N900 comes with 2 network ports, one of which (beside the four LEDs) is intended to connect 
local PC or switches and the other is intended to connect service provider to upper level router. 
N900 can be powered using the DC power supply shipped with the box or using Power over 
Ethernet (PoE) through WAN port. Using power supply is very straightforward. Just plug the jack 
of the power supply into the power outlet on the wireless router. When you install N900 
outdoor and there is no power outlet around, PoE is a good solution.  The black adapter is PoE 
power supply. It comes with 2 ports: POE and LAN. LAN is used to connect the router or Modem. 
POE is used to connect to the WAN port of N900. 

 

Содержание LEGUANG N900



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды