Actel ProASIC3/E Скачать руководство пользователя страница 65

Страница: 65 / 106

Step 8 – Program the Device

ProASIC3/E Starter Kit User’s Guide and Tutorial

To save the log file:

From the File menu, click

Save Log

. The Save dialog box will appear, as shown in

Figure 7-49

Figure 7-49. Save Log File Dialog Box

Select a directory, type in the file name, and click

Save

. The FlashPro software saves the file.

Check Functionality of Tutorial Design

After programming the device, you will see “ACTEL A3PE STARTER KIT” display on the LCD panel as well as
flashing LEDs. There are 6 switches (SW) equipped with special functions.

Press

SW1

to Asyn_Clear on the flashing LEDs and the LCD panel.

Press

SW6

to change the LEDs from flashing to counting.

Press

SW3

to Asyn_Load the counter.

Press

SW2

to change the up counter to down counter.

Press

SW4

for LEDs manual clock.

Press

SW5

for LCD manual clock.

Содержание ProASIC3/E











































































































Результаты поиска

Содержание ProASIC3/E

Отзывы:

Actel ProASIC3/E, Руководство пользователя, Страница: 65 / 106

Результаты поиска

Содержание ProASIC3/E

Отзывы: