Actel ProASIC3/E Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 106

Actel ProASIC3/E Скачать руководство пользователя страница 21

LVDS Channels

ProASIC3/E Starter Kit User’s Guide and Tutorial

21

The 4 differential pairs (consisting of 8 I/O pins) are terminated as shown in

using the color convention on the

first RJ45 connector (which we’ll call “CAT 5E Primary” for the purposes of differentiating it).

The 4 differential pairs (consisting of 8 I/O pins) are terminated as shown in

using the following color

convention on the second LVDS connector (which we’ll call “CAT 5E SECONDARY” for the purposes of
differentiating it).

Note:

The colors refer to the colors that will appear on the CAT 5E cable. The pin numbers correspond to the pin
numbers of an RJ-45 connector. Note that the CAT-5E PRIMARY connections are labeled for the purposes of
what is regarded as standard connections for CAT-5E on Ethernet-type connectors. The connections on the
CAT-5E SECONDARY are reversed so as to allow a standard patch cable to check loopback on these LVDS
signals.

A 1-foot CAT5 standard patch cable supplied with the PA3 evaluation kit can be used for LVDS signals loopback.

Table 2-5 · Color Convention on CAT 5E Primary

White/Orange

p1

TX1+

Orange

p2

TX1–

White/Green

p3

RX1+

Blue

p4

TX2–

White/Blue

p5

TX2+

Green

p6

RX1–

White/Brown

p7

RX2+

Brown

p8

RX2–

Notes:

1. TXn+ refers to positive signal of the transmit side of balanced signal Transmission.

2. TXn– refers to negative signal of the transmit side of balanced signal Transmission.

3. RXn+ refers to positive signal of the receive side of balanced signal Transmission.

4. RXn– refers to negative signal of the receive side of balanced signal Transmission.

Table 2-6 · Color Convention on CAT 5E Secondary

White/Orange

p1

RX3+

Orange

p2

RX3–

White/Green

p3

TX3+

Blue

p4

RX4–

White/Blue

p5

RX4+

Green

p6

TX3–

White/Brown

p7

TX4+

Brown

p8

TX4–

«
...
19
20
21
22
23
...
»

Содержание ProASIC3/E











































































































Отзывы:

Нет отзывов