Actel ProASIC3/E Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 106

Actel ProASIC3/E Скачать руководство пользователя страница 19

FPGA – LCD Interface

ProASIC3/E Starter Kit User’s Guide and Tutorial

19

FPGA – LCD Interface

An 8 × 1 LCD module is provided on the ProASIC3 Evaluation board for demonstrating the board’s functionality.

provides detailed information about the LCD module.

Description

The LCD module MDLS-81809-SS-LV-G-LED-04-G can be operated in either 4-bit data mode or 8-bit data mode.
In this PA3 evaluation board, the above LCD module is being operated in 4-bit data mode to minimize the number of
FPGA lines committed to the interface. The 4-bit data lines (DB4, DB5, DB6, and DB7) and the required control
signals for this LCD module, specifically RS (Register Select), R/~W (Read/~Write), and E (Enable) lines, are driven
from BANK0 I/O lines of FPGA. These BANK0 I/O lines of FPGA are configured as LVTTL outputs for driving the
LCD.

Both V

CCI

and VMV power points of Bank0 are from a fixed 3.3 volts source, thereby enabling BANK0 to function in

LVTTL mode.

The interconnection details between the FPGA and the LCD module are listed in

Table 2-4 on page 19

.

Table 2-3 · LCD Module Details

Part Number

MDLS-81809-SS-LV-G-LED-04-G

Manufacturer Name

VARIRONIX

Display Type

STN - Super-Twisted Nematic

Display Mode

Transflective

Display Format

8 × 1

Character Format

5 × 8 Dots

Character Size

6.45 mm × 10.75 mm

Backlight

LED Backlighting - Green

Viewing Area

61mm × 15.8mm

Operating Temperature

-5°C to +50°C

Voltage-Supply

5 V

Table 2-4 · FPGA – LCD Interconnections

FPGA Pin No.

LCD Pin No.

LCD Pin Name

197

14

DB7

198

13

DB6

194

12

DB5

193

11

DB4

192

5

R / ~W (Read / ~Write)

191

4

RS (Register Select)

190

6

E (Enable)

«
...
17
18
19
20
21
...
»

Содержание ProASIC3/E











































































































Отзывы:

Нет отзывов