manualshive.com logo in svg

ACT ACT 10 DIGITAL KEYPAD, Инструкции по эксплуатации и монтажу

Поделиться
Скачать
ACT ACT 10 DIGITAL KEYPAD Скачать руководство пользователя страница 2

Installation Notes

• Always remember to factory default the controller before you start programming.

• Always remember to place the supplied Varistor across the terminals of the lock terminals to protect

the relay contacts.

• Never use the onboard relay to switch AC mains voltage. An external relay isolated electrically from

the ACT 10 should be used for this purpose.

• Don’t forget to change the programming code to something known only to yourself.

Important

: As with any Access Control system, always ensure there is an alternate means

of escape in the event of the unit failing to operate due to power loss or in the event of fire.

ACT 10 Digital Keypad Operating & Installation Instructions

2

ACT 10 Digital Keypad

ACT 10

ACT 10 Flush Kit

ACT 10 FK

ACT 10 Weather Shield

ACT 10 WS

Ordering Information

Product Specification

Number of Users

10 PIN Codes

Supply Voltage

12 – 24 Volts AC or DC

Current Consumption

40mA (nominal), 120mA (maximum)

Operating Temperature

-10 to +50 degrees C

Door Open Time

0 - 255 seconds

Relay Contact Rating

5A / 250Vac

Controller Size

(H x W x D):

138 x 87 x 37 (mm)

Controller Weight

700 grams

Installation

Indoor or Outdoor (IP54)

Mounting

Surface or Flush

Output Rating

100mA

Содержание ACT 10 DIGITAL KEYPAD









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды