manualshive.com logo in svg

ACS Marvair MAA1020H, Руководство по установке и эксплуатации

Поделиться
Скачать
ACS Marvair MAA1020H Скачать руководство пользователя страница 61

61

Marvair Wall Mount Heat Pump I&O Manual

06/2023 Rev.7

Heating Mode Stop (Mechanical Heating Heat Pump)

Adjust the heating setpoint to approximately two degrees below the current indoor temperature. The 

unit will sequence off, stop heating.

 

Did the Compressor stop? .................................................................................................

❒

Yes  

❒

No

 

Did the Condenser Fan (CFM) stop? ................................................................................

❒

Yes  

❒

No

 

Did the indoor blower motor (IBM) Stop? .......................................................................

❒

Yes  

❒

No

** If you see readings that are out of the normal range or features that seem to be operating incor-

rectly. **

Please provide a description of the issue in the Notes section below and if you need help, call:

Marvair Technical and Warranty Support: (888) 726-2734

This number is manned M-F, 8:00am to 5:00pm eastern.

Technical support calls will be returned M-F, 5:00pm to 8:00pm eastern.

Only Emergency Dispatch calls will be returned M-F, 8:00pm to 8:00am Eastern (and week-

ends & holidays).

Notes: 

____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________

Содержание Marvair MAA1020H






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды