background image

 

ACR101I – Reference Manual

 

[email protected] 

Version 1.01 

www.acs.com.hk 

Page 4 of 21

 

 

 

2.0. Features 

 

USB Combo Device – Works as a smart card reader and mass storage 

 

USB 2.0 High-speed Interface 

 

Bus-powered – No need for separate power supply or battery 

 

Plug and Play – CCID support brings utmost mobility 

 

Extractable USB Connector 

 

Smart Card Reader: 

o

 

Supports ISO 7816 Class A, B and C (5 V, 3 V, 1.8 V) SIM-sized cards 

o

 

Supports microprocessor cards with T=0 or T=1 protocol 

o

 

Supports memory cards using Synchronous Card APDU 

o

 

Supports Specification 11.11-compliant GSM cards 

o

 

Supports PPS (Protocol and Parameters Selection) 

o

 

Features Short Circuit Protection 

 

Application Programming Interface: 

o

 

Supports PC/SC 

o

 

Supports CT-API (through wrapper on top of PC/SC) 

 

Flash Drive: 

o

 

Supports Micro SD cards 

o

 

Maximum of 8 GB memory 

 

Contactless Feature: 

o

 

Embedded MIFARE Classic (1K) chip 

 

Supports Android™ 3.1 and above

1

 

 

Compliant with the following standards: 

o

 

ISO 7816 

o

 

CE 

o

 

FCC 

o

 

VCCI 

o

 

PC/SC 

o

 

CCID 

o

 

Microsoft® WHQL 

o

 

RoHS 2 

o

 

REACH 

 

 

 

 

                                                      

1

 PC/SC and CCID support are not applicable 

Содержание ACR101I






















Отзывы: