Acromag AcroPack AP512 Скачать руководство пользователя | Manualshive

Страница: 29 / 44

background image

AP512 ACROPACK

USER

’S MANUAL

Acromag, Inc. Tel: 248-295-0310

- 28 - http://www.acromag.com

- 28 -

https://www.acromag.com

3.2.9 MCR - Modem Control Register (R/W)

The Modem Control register controls the interface with the modem or data
set as described below.

For model AP512, RTS is used to enable the transceiver to enable output of
TxD. The four modem control inputs (CTS, DSR, DCD, and RI) are
disconnected from their receiver input paths. In addition, the four modem
control outputs (DTR, RTS, OUT1, and OUT2) do not have transmitter output
paths.

Bit-

3 of this register must be set to a logic “1” to enable the corresponding

port to issue an interrupt.

Table 3.10 Modem Control

Register

MCR
Bit

FUNCTION

PROGRAMMING

0

Data Terminal
Ready Output
Signal (DTR)

0= DTR* Not Asserted (Inactive) 1= DTR*
Asserted (Active)

1

Ready to Send
Output Signal
(RTS)

0 = RTS* Not Asserted (Inactive)

1 = RTS* Asserted (Active)

2

Not Used

No Effect on External Operation

3

Port Interrupt
Disable/Enable

0 = Interrupt Disabled for this
port.

1 = Interrupt Enabled for this
port.

4

Loop-back

1

0 = Loop-back Disabled

1 = Loop-back Enabled

5

2

Xon Control

0 = Disable Xon

1 = Enable any Xon function. In this mode
any RX character received will enable Xon.

6

2

Not Used

Must be logic 0

7

2

Divide by Four

0 = Divide by one. The crystal frequency is
unchanged.

1 = Divide by four. After the crystal
frequency is divided by 16 it is further
divided by 4 (see Table 3.2).

«
...
27
28
29
30
31
...
»

Содержание AcroPack AP512













































Отзывы:

Нет отзывов

Похожие инструкции для AcroPack AP512

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: VAT Страницы: 27

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Warren rupp Страницы: 18

Бренд: Yamaha Страницы: 100

GRASS VALLEY MDX-3901

Бренд: Belden Страницы: 45

Бренд: Maximum Controls Страницы: 58

Бренд: Telit Wireless Solutions Страницы: 45

Бренд: YOKOGAWA Страницы: 33

Бренд: Yoshitake Страницы: 18

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренд: Srne Страницы: 13

Wired Manager - DALI

Бренд: Encelium Страницы: 8

Бренд: Madas Страницы: 10

Бренд: X10 Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды