Acrel ARTM, Руководство по эксплуатации

Страница: 11 / 24

7
state, which set up the cycle time interval of each channel temperature value, enter into the value set, the set range 0 ~ 20,
where 0 means normal mode shows a static channel temperature value, the rest of the numerical display of cycle in the
normal mode namely time interval (unit: second). Enter the "DISP" state after the enter confirmation.
设定静态显示，在正常模式下按住左或右键不放，可快速切换到需要的通道温度显示，并保持。
Set the static display, press left or right button in normal mode, can accelerate the switch to the required channel
temperature display, and maintain.
设定循环显示，在正常模式下按住右键不放，可加快循环显示速度。
Set the cycle to display, under normal mode, hold right button, can speed up the circulation display speed.
（
4
）
“
BUS
”
状态设置
（
4
）
“BUS” state setting
进入系统设置模式以后，按左或右方向键直到显示
“ BUS ”
，即通讯设定，回车确认后显示
“ Addr ”
状态，再次
回车后就可以设置地址的值，通过左或右方向键改变地址值，按回车确认后返回
“ Addr ”
状态，按左或右方向键
选择
“ Baud ”
状态，回车进入后通过左或右方向键选择合适的波特率，按回车键确认退出。
Enter the system after setting mode, press left or right direction until the show
"Bus"
, namely the communication
setting, press enter to confirm after the "Addr" status display, enter again after can set the value of address, change
address values by left or right direction key, press enter to confirm back the "Addr" status, according to the left or right
direction key to choose "Baud" state, after enter into by left or right direction key to choose the appropriate Baud rate,
press enter to confirm.
显示状态
Display state
解释
Explanation
可设定范围
Adjustable range
Addr
通讯地址
Communication address
0001
～
0247
Baud
通讯波特率
Communication baud rate
1200
、
2400
、
4800
、
9600
、
19200
（
5
）
“ n.cod ”
状态设置
（
5
）
“n.cod”
state setting
进入系统设置模式以后，按左或右方向键直到显示
“ n.cod ”
，即设置新的系统密码，按回车进入后，按左或
右键输入合适的新密码后，按回车确认。
Enter the system after setting mode, press left or right direction until the show "n.cod" , set up new system
password, press enter to enter, press the left or right input right after the new password, and press enter to confirm.
（
6
）
“
UErn
”
状态设置
（
6
）
“UErn” state setting
进入系统设置模式以后，按左或右方向键直到显示
“ UErn ”
，即查看产品软件版本号，按回车后进入查看状
态。
After entering the system setting mode, press the left or right arrow keys until the "UErn" is displayed, that is,
check the product software version number, and press enter to enter the viewing status.
2.3.3
保存设置选择
2.3.3 Save Settings selection
全部参数设置完成后，在上述六个状态中的任意一个状态下按
“SET”
键，进入
“ SAUE ”
状态，即保存数据。
此时，按回车键保存设置的内容，按
“ SET”
键直接退出系统设置模式，不保存所设置的内容，返回正常模式后按
原有参数运行。
After all the parameter Settings are completed, press the "SET" button in any of the above six states to enter the
"SAVE" state, which is to save the data. At this time, press enter key to save the Settings, press the "SET" key to
directly exit the system setting mode, do not save the contents SET, return to normal mode and follow the original
parameters.