manualshive.com logo in svg

ACPro AC Pro C Series, Руководство по установке

Поделиться
Скачать
ACPro AC Pro C Series Скачать руководство пользователя страница 58

58

Technical Information

4. The high-voltage and low-voltage lines should be fixed separately and securely, with internal big clamps for the former and

small clamps for the latter.

5. Tighten the indoor/outdoor connection cord and power cord respectively on the terminal boards with screws. Faulty

connection may cause a fire.

6.  If the indoor unit connection cord (to the outdoor unit) and power supply are wired incorrectly, the air conditioner may be

damaged.

7. Connect the indoor unit connection cord properly based on the corresponding marks as shown in Figure 3-4-4.
8.  Ground both the indoor and outdoor units by attaching a ground wire.
9.  Unit shall be grounded in compliance with the applicable local and national codes.

6. Electric wiring of outdoor unit side

NOTICE!

 When connecting the power supply cord, make sure that the phase of the power supply matches with the exact 

terminal board. If not, the compressor will rotate reversely and run improperly.
Remove the big handle (18k~30k) /front board (36k~48k) of the outdoor unit and insert the end of the communication cord 
and the power cable into the terminal board.

Single phase: 

U-Match Series DC Inverter Service Manual

92

④

.

The high-voltage and low-voltage lines should be fixed separately and securely, with internal big clamps for the 

former and small clamps for the latter.

⑤

.

Tighten the indoor/outdoor connection cord and power cord respectively on the terminal boards with screws. Faul ty 

connection may cause a fire.

⑥

.

If the indoor unit connection cord (to the outdoor unit) and power supply are wired incorrectly, the air conditioner

may be damaged.

⑦

.

Connect the indoor unit connection cord properly based on the corresponding marks as show n in Figure 3-4-4.

⑧

.

Ground both the indoor and outdoor units by attaching a ground wire.

⑨

.

Unit shall be grounded in compliance with the applicable local and national codes.

(6)  Electric wiring of outdoor unit side

NOTICE!

When connecting the power supply cord, make sure that the phase of the power supply

matches with the exact terminal board. If not, the compressor will rotate reversely and run improperly.

Remove the big handle (18k~30k) /front board (36k~48k) of the outdoor unit and insert the end of the 

communication cord and the power cable into the terminal board.

Single phase:

18k~30k

36k~48k

1

2

1

2

L1   L2

L1   L2

Figure 3-4-8 

Содержание AC Pro C Series



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды