manualshive.com logo in svg

Acom 700S, Руководство по эксплуатации, Страница: 6 / 30

Поделиться
Скачать
Acom 700S Скачать руководство пользователя страница 6

66

W A R N I N G  

 HIGH VOLTAGE!

Both the mains voltage and the high DC voltage up to 500V

inside  the  ACOM  700S  amplifier  are  LETHAL!  For  your

safety, disconnect the power plug from the mains and WAIT

AT LEAST three minutes EACH TIME, BEFORE removing the

cover of the amplifier.

W A R N I N G  

 HIGH VOLTAGE!

NEVER ALLOW, ESPECIALLY CHILDREN, to insert anything

into holes in the case - this may cause ELECTRIC

SHOCK! Never touch an antenna or antenna isolators

during  transmission  or  tuning  -  this  may  result  in  an 

electric shock or burn. Never expose the amplifier to rain,

snow  or  any  liquids.  Avoid  placing  the  amplifier  in

excessively  dusty  environments  or  in  direct  sunlight.  DO

NOT OBSTRUCT COOLING ducts or vents.

W A R N I N G

Do not undertake repairs or changes in hardware or firmware

of your ACOM 700S amplifier. Doing so will endanger your

or  others‘  health  or  life,  or  damage  the  amplifier  and

the  equipment  connected  to  it.  Such  repairs  or  changes

are  not  covered  by  the  warranty  and  may  void

the  warranty.  The  manufacturer  is  not  liable  for  any

such repairs or changes. Any such repairs or changes are

sole  responsibility  of  the  person  or  persons  engaging  in

them.

C A U T I O N

To avoid damage (not covered by the warranty) please read the

INSTALLATION  -  Section  2  of  this  operating  manual  carefully.

If  you  have  any  doubts  or  questions  regarding  the  installation,

operation or safety of the ACOM 700S amplifier, please consult

your dealer immediately.

2.  INSTALLATION

2-1. 

Unpacking and Initial Inspection

C A U T I O N 

Before  you  commence  installing  the  ACOM  700S  amplifier, 

please  read  this  manual  thoroughly.  Carefully  inspect  the 

shipping carton and its contents as described below for missing 

items (S. 1-3) or mechanical damages. If anything is missing or 

is  damaged  (scratched,  bent,  crushed  or  something  is  rattling 

inside  or  moving  freely  when  turning  the  amplifier  over, 

notify 

your dealer immediately!

 Delaying this notification may infringe 

the insurance conditions of the carrier.

Содержание 700S































Отзывы:

Нет отзывов