ACME Poly-tunnel Скачать руководство пользователя страница 5

V. Assembly Instructions 
 

A) Preparing the site 

1.

Clear the area from vegetation and 
debris. 

2.

Level the ground if necessary. 

3.

Outline 

the rectangular footprint of the 

greenhouse with 4 sticks connected by 
string. 

 

B) Assembling the frame 

1.

Place ground pegs

 (

a

) inside the string every 

1.47m on the long sides and at each corners. 

2.

Drive the pegs into the ground

 using a 

sledgehammer. Cushion each peg's head with a 
piece of timber so it does not get distorted. Leave 
20cm (8") of the peg stick out so the stopping 
screw is just above ground level. 

3.

Before 

assembling the hoops

, verify that the end of each half hoop (

b

slides onto its respective ground peg. File the tubes if they do not fit. 

4.

Join each half hoop pair with a cross clamp

 (

i

) on the 

ground. 

5.

Mount the first 2 hoops

 on the ground pegs. 

6.

Install a ridge bar

 (

c

) between the 2 first hoops. 

Attach the extremities of the ridge bar onto the 
hoops with a cross clamp (

i

), filleted tips facing down.  

7.

Mount the next hoop

 and connect it to the previous 

one with a ridge bar. 

Repeat until all 11 hoops are 

assembled

8.

Place Q-clips 

(

j

)

 on the end-hoop

 and on the extremities of a prop bar

 

(

d

).

©Acme Polytunnels-2018

 of 

5

8

5.8m

15m

To ensure the corners form 90º angles, move the opposite stakes so the diagonals are the 

same length.

c

i

a

b

Содержание Poly-tunnel









Отзывы: