manualshive.com logo in svg

aci SNOWSPORT HD Utility Plow, Руководство по установке, Страница: 8 / 16

Поделиться
Скачать
aci SNOWSPORT HD Utility Plow Скачать руководство пользователя страница 8

8

2: ASSEMBLING SNOWPLOW

NOTE:

 Rubber cutting edge should be room temperature before assembling.

A. Align groove on rubber cutting edge with groove in lower aluminum blade.  
B. Slide rubber cutting edge into matching channel of lower aluminum blade and center. 

TIP:

 Apply soapy water solution to top of rubber cutting edge and aluminum blade 

mounting channel for easier assembly.

Lower aluminum blade

Back side of blade

C. Turn rubber cutting edge and lower aluminum blade over and set on wood blocks, one 

at each end. 
D. Connect tongue and groove joint of upper and lower aluminum blade. Slide upper 

aluminum blade until centered with lower aluminum blade.

TIP: 

Once upper blade is centered, apply locking pliers on tongue and groove joint to 

ensure upper and lower aluminum blades remain aligned.

Upper aluminum blade

Rubber 

cutting edge

Lower aluminum blade

Use 2x4 to prop blade 

up at both ends

Tongue and groove joint

Apply locking pliers here

Rubber cutting edge

Содержание SNOWSPORT HD Utility Plow

















Отзывы:

Нет отзывов