background image

49

 

 

 

 

DAILY CHECKS

 

For your  own  safety and to  assure the long 
life of your machine, a careful check should 
be made before each operation.

 

 

 

Coolant Check

 

 

CAUTION

 

To avoid personal injury:

 

 

Move  the  excavator  to  even 
ground.

 

 

Make  sure  that  the  engine  is 
turned off.

 

 

Do  not  open  the  radiator  cap 
right  after  the  engine  has 
been  stopped;  Serious  burns 
can  occur  from  contact  with 
escaping hot coolant fluid.

 

 

Check  the  coolant  level  in  the 
reserve  tank  only  after  the 
engine has cooled down.

 

 

Remove the radiator cap only if 
absolutely necessary.

 

 

The radiator has a reserve tank. Should the 
coolant level in the radiator sink, the water 
will  be  automatically  be  transferred  to  the 
radiator.

 

Check the coolant level in the reserve tank 
and  fill  up  if  necessary.  The  coolant  level 
should  be  between  the  marks  “FULL”  and 
“LOW”.

 

 

 

 

IMPORTANT:

 

 

Do not fill the reserve tank over the 
“FULL” marking.

 

 

Do not fill with dirty or salty water.

 

 

NOTE:

 

 

Before  delivery  coolant  were  filled  with 
50 % water and 50 % antifreeze.

 

 

 

Check Fuel Level

 

 

CAUTION

 

To avoid personal injury:

 

 

Stop the engine and remove 
the key before fueling.

 

 

Do not smoke while fueling.

 

 

IMPORTANT:

 

 

Temperatures  over  –5ºC,  use  No.2-D 
diesel fuel, temperatures are under –5ºC, 
use No.1-D diesel fuel.

 

 

Make sure that the fuel tank is not empty. 
Air  will  enter  into  the  fuel  system,  and 
must be purged before restarting.

 

 

Always fill up fuel after a day's work.

 

 

See “PURGING OF THE FUEL SYSTEM” 
in 

“OTHER 

ADJUSTMENTS 

AND 

REPLACEMENTS”.

 

 

1.

 

Check the fuel level of the indicator.

 

 

 

3

 

3

 

Содержание A14SE

















































































Отзывы: