BUTTON OPERATIONS
Clock, RPM,SPC, Wheel, Pulse, Units, *TEMP, **fuel & ODO SET UP
1. Setup operations include 12H/24H clock, shift warning RPM, engine signal, wheel circumference, speed pulses, units, temperature units, warning
temperature, fuel sender resistance selection and odometer adjustment. You have to set up step by step. The computer will be automatically
revert to main screen if no button operation for 75 seconds in any setting screen.
2. Push the button to reach the “xx.xV and Set” screen, then hold the button for 2 seconds to go into the setting mode. In setting mode, each press
of the button increments the flashing digit by 1 or converts units. Hold the button for 2 seconds to confirm the digit setting and jump to next
setting screen or digit, until the last setting mode then go to normal mode.
3. It displays "12 or 24H and XX:XX:XX " symbols and AM/PM when you select 12H. Operate button as described in item 2 to finish clock setting and
jump to shift RPM warning setting.
4. It displays the default "r06500 RPM", the digits “06” flashes. Follow the item 2 of button operation to finish the shift RPM warning setting and jump
to engine specification setting.
5. It displays "SP 1r1P and RPM", the default value is 1r1P; there are 5 options: 1r1p, 2r1p, 1r2p, 1r3p, 1r4p. “r” means the numbers of engine
rotation, “P” means number of signals from engine. For example the value 2r1P means the engine rotates 2 turns to output one signal.
6. Press the button to move in loop sequence from one to another value of the 5 values. Hold the button to confirm the setting and go to wheel
circumference setting screen
7. It displays "cXXXX", "c" means "Circumference", following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to
finish the wheel circumference setting and jump to speed pulses setting.
8. It displays "P-001", the pulses screen, the number of pulses into the computer per turn of the wheel. Follow item 2 of button operation to finish the
setting and jump to unit setting.
9. It displays Km/H or MPH, each press of the button converts unit; hold the button for 2 seconds to confirm unit setting and jump to temperature
unit setting.
10.It displays “100.0Km/H & on” or “100Km/H & oFF”, the decimal point will disappear when Off is selected. Follow the item 2 of button operation to finish the
decimal setting and jump to temperature units setting.
11. * It displays "
°C
,
°F
or oFF", each press of the button converts
°C
,
°F
or Off, the temperature bars will disappear when you select oFF mode; hold
the button for 2 seconds to confirm temperature unit setting and jump to temperature warning setting.
12. * It displays "XXX°" and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sender
resistance setting.
13. ** It displays “100r”, follow the item 2 to select 100Ω, 250Ω, 510Ω, oFF, -100Ω, -250Ω or -510Ω and jump to odometer setting.. The fuel meter bar
will disappear if you select oFF mode.
14. It displays “ODO & 00000X Km/H or MPH”, the “X” is from odometer testing in factory, follow item 2 to set a desired odometer value and return to
Normal Mode. This setting screen will disappear when the odometer is over 30km (18.6Miles) or your setting is over 30km
Press and hold Button for 2 sec.: Reset operation
1. Press and hold the button for 2 seconds to reset data at the screen.
2. Press the button to reach the desired screen then press and hold the button for
2 seconds to reset TRIP, RT, MAX, AVG and MAX RPM data from stored values to zero.
3. ODO, HRT and TT data cannot be reset.
RESET
2sec
Get to SETUP mode:
1. Push the button until the V & Set screen appears when the bike is stationary
2. Press and hold the button for 2 seconds to go into the set mode.
3. Follow the set up instruction to set up data.
Shift Warning RPM Operation:
1. Press the button to reach the RPM screen; pull on the throttle until the desired shift warning RPM.
2. Press and hold the button for 2 seconds to confirm and set up the shift warning RPM.
3. Warning LED will flash to remind you shift gear.
4. Press and hold the button for 2 seconds to re-setup another value of shift warning at the RPM screen.
Push Button: Change mode
1. Briefly push the button to move in loop sequence from one function screen to another.
2. Push the button to move between all functions in sequence as “ ” from one function screen to another when the bike is stationary.
3. Push the button to move partial functions in loop sequence as “ ”when speed sensor detects signal input.
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
2sec
reset
**
*
*
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
The bike is stationary
*
*
20171123
