BUTTON OPERATIONS
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for 2 seconds to reset TRIP
1, Trip 2, MAX, Max. temperature and MAX RPM data from stored values to zero individually.
2. The data of Trip 1, AVG & RT be reset at the same time when one of the 3 data functions is
being reset.
3. ODO, clock and TT data cannot be reset.
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence from one function screen to another.
SHIFT RPM WARNING OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired shift RPM warning displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer will flash to warning you shift gear.
4. Operate items 1 & 2 to readjust the shift warning RPM.
WHEEL CIRCUMFERENCE TABLE
1. The details below have been calculated using the following formula; Tire Diameter (inch) x 25.4(mm/inch) x 3.1416 = wheel circumference (in mm).
2. Identify the tire size of your ATV/Motorcycle when you need to change different tire, and key in the corresponding number shown in the following chart.
UNIT & WHEEL CIRCUMFERENCE SETTING
Circumference
Tire Size
Tire Size
Circumference
Tire Size
Circumference
1436mm
18 inch
1357mm
17 inch
1277mm
16 inch
1197mm
15 inch
19 inch
1516mm
1756mm
1676mm
1596mm
22 inch
21 inch
20 inch
2075mm
1995mm
1915mm
1835mm
23 inch
26 inch
25 inch
24 inch
1. Setup operations include 12/24hour clock, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units of
odometer, units of temperature and temperature warning. These must be set up step by step. The computer will automatic reversion
to main screen if no button operation for 75 seconds at any setting screen.
2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1
or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE
button for 2 seconds at any setting screen to finish the setting and go to main screen.
3. It displays "12 or 24H and XX:XX-XX" symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to
finish clock and jump to shift RPM warning setting.
4. It displays " RPM rXXX00 ". Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine
specification setting.
5. It displays "SPC-X.X RPM", the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine
rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal.
6. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting
and go to wheel circumference setting screen.
7. In "cXXXX" display, "c" means "Circumference", following 4 default digits; flashing digit is digit to be set. Follow the item 2 of
button operation to finish the wheel circumference setting and jump to unit setting.
8. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to
temperature unit setting.
9. It displaysm " " , each press of RESET button converts or ; press MODE button to confirm temperature setting and jump to
temperature warning setting.
10. It displays " 105" and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to
main screen.
RESET
2 sec
mode
reset
+
2 sec
mode
mode
mode
mode
mode
reset
mode
2 sec
mode
mode
mode
mode
reset
mode
mode
mode
mode
mode
mode
mode
mode
mode
℃
℃
℉
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
TEMPERATURE WARNING
1. The LCD screen will jump to temperature screen automatically when the sensor detects temperature higher than the presetting warning temperature.
2. The temperature digits flashes and both buttons are out of function during over temperature.
3. Stop engine until temperature cooling down to below presetting warning temperature, both bottons recover to work.
