FUNCTIONS
Specific Hall sensors:
The sensor such as Honda CRF, XR….etc. can replace original
sensor cable and fix it at the original position.
Hall Effective Speed Sensor and Magnet:
1. This is universal sensor for ATV rear wheel installation or
motorcycle front wheel installation as if you purchase a
relative speed sensor holder.
2. Find a part can rotate to install magnet and a location can
install sensor and the sensor can be aligned to the magnet.
3. Align the center of the magnet to center of side face of
the sensor.
4. Make sure the gap between the magnet and the sensor
is within 5mm.
BAR RPM: Bar Graphic Tachometer
The bar tachometer has 10,000rpm and 20,000rpm options.
RPM: Digital Tachometer
1. It displays digital tachometer up to 19,900RPM and displays
19,999rpm when tachometer is over 20,000rpm. .
2. Tachometer signal can pick up from either CDI or Ignition Coil Signal.
MAX RPM: Maximum Tachometer
Displays highest tachometer achieved after last Reset operation.
Km/H or MPH: Speedometer
Displays speed meter up to 399.9 Km/H or 248.5 MPH.
MAX: Maximum Speed Meter
Displays highest speed achieved after last Reset operation.
AVG: Average Speed Meter
It calculates average speed from last RESET. The AVG is
calculated from TRIP be divided by RT.
TRIP: Trip Meter
TRIP function accumulates trip distance from last RESET as
long as bike/vehicle is being ridden.
ODO: Odometer
1. ODO accumulates total accumulated distance
traveled during bike moving.
2. ODO data is adjustable when it is less than 30km (Miles),
after that it stored in memory and couldn’t be reset.
RT: Riding Timer
1. Calculates total running time from last RESET.
2. Count automatically begins with movement.
RT: Hour Meter
1. Calculates total engine operation time from last RESET.
2. Count automatically begins with engine starting.
TT: Total Hour Meter
1. Calculates total engine operation time from the
beginning of the bike.
2. TT data is stored in memory, and couldn’t be reset.
:
12/24 hour Clock
Displays 12 or 24 hour current time.
:
Fuel Gauge
1. Has 7 bars to indicate how much fuel remains.
2. Built-in 100, 250, 510Ohm, oFF, -100, -250 and -510 Ohm fuel
sender resistance, the fuel bars will disappear when you
select “oFF” mode.
3. The full bars are low resistance and empty bar is high
resistance for 100, 250 and 510ohm; -100, -250 and -510
ohm are the inverse.
4. Last bar flashes to indicate low fuel level automatically.
RESET BUTTON
1. Press MODE button to the desired screen then press RESET
button for 2 seconds to reset hour meter, MAX SPD,MAX
RPM data from stored values to zero individually.
2. The data of Trip, AVG & RT can be reset at the same time
when one of the 3 data functions is being reset.
3. ODO, clock and TT data cannot be reset.
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
BUTTON OPERATIONS
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence
as “ ” path from one function screen to another when the
speed sensor does not detect any signal input.
2. Press the MODE button to move partial functions in loop
sequence as “ ” path when speed sensor detects signal
input.
Low Fuel Level Warning
Last bar and low fuel warning indicator flash to indicate low fuel
level automatically.
SHIFT WARNING RPM OPERATION
1. Press MODE button to the RPM screen; pull on the throttle
until the desired shift warning RPM.
2. Press RESET button to confirm and set up the shift warning
RPM.
3. Bar-graphic tachometer and warning LED will flash to
warning you shift gear.
4. Press RESET button for 2 seconds at the RPM screen to
re-adjust the shift warning RPM.
Backlight of Internal/Bike’s Powers
1. The computer built-in a CR2032 battery for off road bikes in case
take away bike’s batter to reduce weight.
2. You can use both internal battery and bike’s battery at the same
time.
3. The backlight is always turned on if you connect to bike’s battery;
backlight will be turned on 3 seconds then turn off automatically
by each press of any button when using internal power status.
4. Once connect to bike’s battery, button operations will be switch
off when switch key power is off. User needs to turn on power
switch key to operating buttons.
:
Low Battery Indicator
1. The “ “ icon flashes when the CR-2032 battery is at low power
status to reminder you change the battery.
2. All setting is kept in memory not mater the power is connected to
bike’s 12VDC battery or using internal CR2032 battery only; In case
the power is only the internal CR2032 battery, the unit can display
riding data but can’t be kept in memory when The “ “ icon
appears in order to avoid setting data be reset at low voltage , that
means riding data from last memory until the icon appears is lost.
3. Remove the old battery. Replace with a new CR2032 with the
positive (+) pole towards the battery cap.
4. Be sure to press RESET button at the rear side after installed the
battery to sure all functions work smoothly.
Bars
-250Ω
-100Ω
510Ω
250Ω
100Ω
7
6
5
4
3
2
1
0-Flash
0-10
11-20
21-35
36-45
46-60
61-75
76-90
91-100
0-25
26-50
51-85
86-110
111-150
151-200
201-230
231-250
0-50
51-100
101-180
181-230
231-300
301-380
381-460
461-510
100-90
89-75
74-60
59-45
44-35
34-20
19-10
9-0
250-230
229-200
199-150
149-110
109-85
84-50
49-25
24-0
-510Ω
510-460
459-380
379-300
299-230
229-180
179-100
99-50
49-0
AUTO Power Off
1. The power will be turned off automatically after 3 minutes the
unit does not receive any signal from speed, RPM or button
operation in case it is using the internal battery CR2032.
2. The riding data will be kept in memory at each power off.
3. The power is always turned on at LAP mode until go out the LAP
mode.
