background image

EN-2

Information  for  your  safety  and

 

comfort

Safety  instructions

Read these instructions carefully. Keep this document for future reference. Follow all

warnings  and  instructions  marked  on  the product.

CAUTION  for  plug  as  disconnecting  device

Observe  the  follwing guidelines  when  connecting  and  disconnecting  power  to  the

power  supply  unit:

Install the power supply unit before connecting the power cord to the AC power outlet.

Unplug the power cord  before removing the power supply unit from the product.

If the system has multiple sources of power, disconnect power from the system by

unplugging all power cords  from  the power  supplies.

CAUTION  for  accessibility

Be sure that the power outlet you plug the power cord into is easily accessible and

located as close to the equipment operator as possible. When you need to disconnect

power to the equipment, be sure to unplug the power cord from the electrical outlet.

Warnings

Do not use this product near water.

Do not place this product on an unstable cart, stand or table. If the

product falls,  it could be  seriously damaged.

Slots and  openings are provided for  ventilation to ensure reliable  operation of

the product and to protect it from overheating. These openings must not be

blocked  or  covered.  The  openings  should  never  be  blocked  by  placing  the

product on a bed, sofa, rug or other similar surface. This product should never

be placed near or over a radiator or heat register, or in a built-in installation

unless  proper  ventilation  is  provided.

Never push objects of  any kind  into this product through  cabinet

slots as they may touch dangerous voltage points or short-out parts that could

result in a fire or electric shock. Never spill liquid of any kind onto or into the

product.

To  avoid damage  of  internal components and  to  prevent battery  leakage,

 

do

not place the product on a vibrating surface.

Never use it  under sporting, exercising, or any vibrating  environ ment which

will probably cause unexpected  short current or damage  rotor devices,  HDD,

Optical drive, and even exposure risk from lithium battery pack.

Safe  listening

Follow  these  instructions,  suggested  by  hearing  experts,to  protect  your  earing.

Gradually increase  the volume  until you can hear it  clearly and  comfortably and

without  distortion.

After setting the volume level, do not increase it afteryour ears adjust.

Limit the amount of time listening to music at high volume.

Avoid  turning  up  the  volume  to  block  out  noisy  surroundings.

Turn the  volume down if you  can’t hear people speaking  near you.

Содержание X243H


























Отзывы: