Acer K272HL Скачать руководство пользователя страница 7

Страница: 7 / 14

ACER K272HL

4. Disassembly and Assembly SOP

K272HL

4.1 Disassembly Procedures

Preparation before disassemble

1.Clean the room for

disassemble

2.Identify the area for monitor
3.Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow;

according to the actual condition plan the

disassemble

layout

4.Prepare the implement, equipment, materials as bellow:

1) working table
2)

Screw-driver: Philips-head screwdriver, Hex-head screwdriver

3) knife
4) glove
5) cleaning cloth
6) ESD protection

After unplugging the power cord, the power board still have power energe. Please pay attention
when disassembling/assembling Power BD.

Disassemble the

(Rear Case)

, stand

and base

Before Disassembling & Assembling, monitor need to be put on the sponge and
the Insulation glove must be wore during the process.

Disassemble

Stand and Base from the RC(Rear Case). Unlock RC screws.

Disassemble RC from monitor.

Disassemble SHD and

Tear down AL-Tape off SHD(Shielding) as picture 1.
Unlock the Hexagonal screws as picture 2.
Unlock 9 MF screws and 2 trim screws as picture 3.

PICTURE 1 PICTURE 2 PICTURE 3

Содержание K272HL















Результаты поиска

Содержание K272HL

Отзывы:

Похожие инструкции для K272HL

Бренды по названию

Популярные бренды

Acer K272HL, Руководство по продлению срока службы

Результаты поиска

Содержание K272HL

Отзывы:

Похожие инструкции для K272HL

Бренды по названию

Популярные бренды