background image

x

Federal Communications Commission

Declaration of Conformity 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) this device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may cause undesired 

operation.  

The following local Manufacturer /Importer is responsible for this declaration: 

 
Product:                                     LCD Monitor  
Model Number:                         DM431K   
SKU Number:                            DM431K xxxxxx;  
                                                   (“x” = 0~9, a ~ z, A ~ Z or Blank)  
Name of Responsible Party:      Acer America Corporation  
Address of Responsible Party:  333 West San Carlos St.                                                              

Suite 1500  

San Jose, CA 95110  

U. S. A.  

Contact Person:                          Acer Representative  
Phone No.:                                 254-298-4000  
Fax No.:                                     254-298-4147 

 Acer America Corporation        

333 West San Carlos St., Suite 1500 

San Jose, CA 95110, U. S. A.  

Tel : 254-298-4000  

Fax : 254-298-4147  

www.acer.com

 

Содержание DM431K





























Отзывы: