background image

 

Never push objects of any kind into this product through cabinet slots as they may 

touch dangerous voltage points or short-out parts that could result in a fire or electric 

shock. Never spill liquid of any kind onto or into the product. 

 

To avoid damage of internal components and to prevent battery leakage, do not place 

the product on a vibrating surface. 

 

Never use it under sporting, exercising, or any vibrating environment which will 

probably cause unexpected short current or damage rotor devices, HDD, Optical drive, 

and even exposure risk from lithium battery pack. 

 

This product is not suitable for use with visual display workplace devices according to 

§2 of the German Ordinance for Work with Visual Display Units. 

 

Using electrical power 

 

 

This product should be operated from the type of power indicated on the marking label. 

If you are not sure of the type of power available, consult your dealer or local power 

company. 

 

Do not allow anything to rest on the power cord. Do not locate this product where 

people will walk on the cord. 

 

If an extension cord is used with this product, make sure that the total ampere rating of 

the equipment plugged into the extension cord does not exceed the extension cord 

ampere rating. Also, make sure that the total rating of all products plugged into the wall 

outlet does not exceed the fuse rating. 

 

Do not overload a power outlet, strip or receptacle by plugging in too many devices. 

The overall system load must not exceed 80% of the branch circuit rating. If power 

strips are used, the load should not exceed 80% of the power strip's input rating. 

 

This product's power supply is equipped with a three-wire grounded plug. The plug 

only fits in a grounded power outlet. Make sure the power outlet is properly grounded 

before inserting the power supply plug. Do not insert the plug into a non-grounded 

power outlet. Contact your electrician for details. 

 

Warning

The grounding pin is a safety feature.   

Using a power outlet that is not properly grounded   

may result in electric shock and/or injury. 

 

Note: 

The grounding pin also provides good   

protection from unexpected noise produced by   

other nearby electrical devices that may interfere   

with the performance of this product. 

Содержание Altos T350 F4























Отзывы: