Acer ALH-608ds Скачать руководство пользователя

Страница: 4 / 32

About this Manual

Purpose

This user manual gives you all the information you need to operate the

AcerHub ALH-608ds dual-speed Ethernet hubs properly.

Note: ALH-608ds is the model number of AcerHub 608ds.This model number

"ALH-608ds" will be used through this manual.

Manual Structure

This user manual consists of Quick Installation Guide, four chapters and one

appendix as follows:

Quick Installation Guide

Chapter 1

Overview

This chapter describes the features and functions of the AcerHub ALH-608ds

hub, and the items in the package.

Chapter 2

Make Your Hub Ready

This chapter describes the installation procedures to quickly make your hub

ready for networking and the easiest way to find out if the hub is working well.

Chapter 3

Building Feasible Networks

This chapter describes the network topology for hybrid 10Mbps and 100Mbps

networks, cabling requirements for connections, and the interoperability

between other hubs and switches. A detailed introduction of the bridged uplink

port will also be given.

Chapter 4

Troubleshooting

This chapter provides a simple troubleshooting guideline that you can follow to

eliminate errors for quick network recovery.

Appendix A

Specifications

608-UM 1/8/99 2:34 PM

≠∂≠

±2

Содержание ALH-608ds

































Результаты поиска

Содержание ALH-608ds

Отзывы:

Похожие инструкции для ALH-608ds

Бренды по названию

Популярные бренды

Acer ALH-608ds, Руководство пользователя

Результаты поиска

Содержание ALH-608ds

Отзывы:

Похожие инструкции для ALH-608ds

Бренды по названию

Популярные бренды