Acer AL2616WD Скачать руководство пользователя | Manualshive

Страница: 16 / 20

background image

15

ERROR MESSAGE & POSSIBLE SOLUTION

CABLE NOT CONNECTED :

1. Check that the signal-cable is properly connected, If the connector is

loose, tighten the connector’s screws.

2. Check the signal -cable connection pins for damage.

INPUT NOT SUPPORT :

Your computer has been set to unsuitable display mode, set the computer to

display mode given in the following table (See page 18).

«
...
14
15
16
17
18
...
»

Содержание AL2616WD





















Отзывы:

Нет отзывов

Похожие инструкции для AL2616WD

ProLite XUB2893UHSU

Бренд: Iiyama Страницы: 31

Бренд: Alecto Страницы: 25

Бренд: IBM Страницы: 151

Бренд: ICP DAS USA Страницы: 6

Бренд: BIOS Diagnostics Страницы: 20

Бренд: 4iiii Страницы: 2

Бренд: Samtron Страницы: 57

14.1" TFT LCD Ceiling Color Monitor/TV

Бренд: Farenheit Страницы: 11

Бренд: protech Страницы: 46

Бренд: switel Страницы: 44

Бренд: I-Tech Страницы: 31

Бренд: K&K Systems Страницы: 16

Бренд: HANNspree Страницы: 23

Бренд: NEOFYTE Страницы: 21

Бренд: Wachendorff Страницы: 15

Бренд: I-Tech Страницы: 28

Life Source UA-851THW

Бренд: A&D Страницы: 72

Бренд: Atari Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды