background image

 

4

INSTALLATION INSTRUCTIONS

 

 

Support Frame

 

 

 

Do not perform a pulling or plugging action when the display is under 

slanting status to prevent the display from ejecting.

 

 

 

Pull out the pin from the display support frame as per the figure and then 
adjust the height. Note that upon pulling out the pin, erect the machine on the 
table to prevent the top part of the display from ejecting.

 

 
POWERCORD 

 

Power Source: 

 

1.  Make sure that the power cord is the correct type required in your area. 
2.  This LCD monitor has an External universal power supply that allows 

operation in either 100/120V AC or 220/240V AC voltage area (No user 
adjustment is required.) 

3.  Connect the AC-power cord into your LCD monitor’s DC-power-input. The 

AC-power cord may be connected to either a wall power outlet or the 
power outlet socket on your PC, depending on the type of power cord 
supplied with your LCD monitor. 

 

NOTES 

 
A certified power supply cord has to be used with this equipment. The relevant 
national installation and/or equipment regulations shall be considered. A 
certified power supply cord not lighter than ordinary polyvinyl chloride flexible 
cord according to IEC 60227 (designation H05VV-F 3G 0.75mm

2

 or 

H05VVH2-F2 3G 0.75mm

2

) shall be used. Alternative a flexible cord be of 

synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm

2

shall be used. 

 

 

 

 

 
 (only AL1922 h/AL1922 r) 

 

Содержание AL1922 r





















Отзывы: